400 Watt Power Inverter UK Plug 230 Volt European with Cables 12 Volt

Modified Sine Wave Power Inverters represent the most economical solution for powering a large number of appliances. The waveform produced by a Modified Sine Wave Power Inverter is blocky resembling a set of steps whereas the waveform produced by utility companies is smooth much like a curvy road. Therefore because of the type of waveform the Modified Sine Wave Power Inverters produce they are suitable for most applications. Modified Sine Wave Power Inverters are more efficient in converting battery power to AC. So if you're looking to make a pot of coffee run a heater or air conditioner or appliances that can withstand occasional electrical noise a Modified Sine Wave Inverter is a cost-effective solution. To select the right inverter first determine what devices you would need to run in the event of a power outage. Then select the appropriate inverter that can carry the combined wattage requirements of these devices. Some appliances have a start up amperage. To see a list of average start up requirements see our Technical Support section on the left nav bar of our website. At AIMS you'll discover our inverters range from 75 watts up to 12000 watts more than enough to power nearly every application imaginable. /This 400 watt inverter is ideal for small devices. Features:

• 400W continuous power
• Modified sine wave
• Green LED on front panel to confirm power on
• Red LED on front panel to warn of a faulty condition
• UK Plug type G 3 prong
• On/off switch
• Over Temperature protection
• Over Load protection
• Includes cigarette lighter connection with built in fuse (To protect the vehicles wiring, the vehicles cigarette lighter adapter can only handle 180 watts,
• Isolated ground neutral
• AC output short circuit protection
• Aluminum case for optimal cooling
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

Specifications

• Continuous output power: 400 Watts
• Surge power capability (peak power): 800 Watts
• dc input / operating voltage: 10 to 16 Volts
• Output voltage: 220/230 Volts AC ~ European/African
• Output wave form: modified sine wave
• Output frequency: 50 Hz
• Battery low voltage alarm: 10.5 +/- 0.5 Volts
• Battery low voltage shutdown: 10.0 +/- 0.5 Volts
• No load current @ 12V: 1 amp
• Full load efficiency: 90%
• 1/3 load efficiency: 95%
• Operating temperature: -10 to 40 C
• AC Output Socket Type: UK Plug type G 3 prong
• High input voltage protection: 16 +/- 0.5
• Low input voltage shutdown: 10.6V +/- 0.3
• Product size (L x W x H): 7.0" X 5.0" X 2.13"
• Unit Weight: 2 lb Boxed Weight: 3 lb

 

AIMS Power 400 Watt Power Inverter UK Plug 230 Volt European with Cables 24 Volt Overview: Modified Sine Wave Power Inverters represent the most economical solution for powering a large number of appliances. The waveform produced by a Modified Sine Wave Power Inverter is “blocky” resembling a set of steps whereas the waveform produced by utility companies is smooth much like a curvy road. Therefore because of the type of waveform the Modified Sine Wave Power Inverters produce they are suitable for most applications. Modified Sine Wave Power Inverters are more efficient in converting battery power to AC. So if you’re looking to make a pot of coffee run a heater or air conditioner or appliances that can withstand occasional electrical noise a Modified Sine Wave Inverter is a cost-effective solution. To select the right inverter first determine what devices you would need to run in the event of a power outage. Then select the appropriate inverter that can carry the combined wattage requirements of these devices. Some appliances have a start up amperage. To see a list of average start up requirements see our Technical Support section on the left nav bar of our website. At AIMS you’ll discover our inverters range from 75 watts up to 12000 watts – more than enough to power nearly every application imaginable. /This 400 watt inverter is ideal for small devices. European 220/230V 50 hz UK plug. Will not work on US 120 VAC equipment. Features:

• 400W continuous power
• Modified sine wave
• Green LED on front panel to confirm power on
• Red LED on front panel to warn of a faulty condition
• UK Plug type G 3 prong
• On/off switch
• Over Temperature protection
• Over Load protection
• Includes cigarette lighter connection with built in fuse (To protect the vehicles wiring, the vehicles cigarette lighter adapter can only handle 180 watts,
• Isolated ground neutral
• AC output short circuit protection
• Aluminum case for optimal cooling
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

Specifications

• Continuous output power: 400 Watts
• Surge power capability (peak power): 800 Watts
• dc input / operating voltage: 20 to 30 Volts
• Output voltage: 220/230 Volts AC - European/African
• Output wave form: modified sine wave
• Output frequency: 50 Hz
• Battery low voltage alarm: 20 +/- 0.5 Volts
• Battery low voltage shutdown: 20 +/- 0.5 Volts
• No load current @ 12V: 1 amp
• Full load efficiency: 90%
• 1/3 load efficiency: 95%
• Operating temperature: -10 to 40 C
• AC Output Socket Type: UK Plug type G 3 prong
• High input voltage protection: 30 +/- 0.5
• Low input voltage shutdown: 20 V +/- 0.3
• Product size (L x W x H): 7.0”X 5.0”X 2.13”
• Unit Weight: 2 lb Boxed Weight: 3 lb

 

AIMS Power 400 Watt Power Inverter with Cables 12 Volt 12 VDC 120 VAC 60Hz Overview: Modified Sine Wave Power Inverters represent the most economical solution for powering a large number of appliances. The waveform produced by a Modified Sine Wave Power Inverter is “blocky” resembling a set of steps whereas the waveform produced by utility companies is smooth much like a curvy road. Therefore because of the type of waveform the Modified Sine Wave Power Inverters produce they are suitable for most applications. Modified Sine Wave Power Inverters are more efficient in converting battery power to AC. So if you’re looking to make a pot of coffee run a heater or air conditioner or appliances that can withstand occasional electrical noise a Modified Sine Wave Inverter is a cost-effective solution. To select the right inverter first determine what devices you would need to run in the event of a power outage. Then select the appropriate inverter that can carry the combined wattage requirements of these devices. Some appliances have a start up amperage. To see a list of average start up requirements see our Technical Support section on the left nav bar of our website. At AIMS you’ll discover our inverters range from 75 watts up to 12000 watts – more than enough to power nearly every application imaginable. Features:

• 400W continuous power
• Modified sine wave
• Green LED on front panel to confirm power on
• Red LED on front panel to warn of a faulty condition
• Dual ac receptacles
• On/off switch
• Over Temperature protection
• Over Load protection
• Includes cigarette lighter connection with built in fuse(To protect the vehicles wiring, the vehicles cigarette lighter adapter can only handle 180 watts,
• Isolated ground neutral
• ac output short circuit protection
• Aluminum case for optimal cooling
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

Specifications

• Continuous output power: 400 Watts
• Surge power capability (peak power): 800 Watts
• dc input / operating voltage: 10 to 16 Volts
• Output voltage: 120 Volts ac
• Output wave form: modified sine wave
• Output frequency: 60 Hz
• Battery low voltage alarm: 10.5 +/- 0.5 Volts
• Battery low voltage shutdown: 10.0 +/- 0.5 Volts
• No load current @ 12V: 1 amp
• Full load efficiency: 90%
• 1/3 load efficiency: 95%
• No load minimum operating temperature: 32 degrees F
• Full load maximum operating temperature: 104 degrees F (automatic shutdown)
• AC Output Socket Type: dual Type 2 -3 prong
• High input voltage protection: 16 +/- 0.5
• Low input voltage shutdown: 10.6V +/- 0.3
• Product size (L x W x H): 7.0”X 5.0”X 2.13”
• Unit Weight: 2 lb Boxed Weight: 3 lb

 

4000 Watt Pure Sine Inverter Charger 12Vdc to 120Vac Output

This 4000 watt inverter charger produces a pure sine wave, which some appliances require for use. So it can run laser jet printers, computers, televisions, CPAP machines and other medical equipment. During a big storm that knocks out electricity, a battery-bank and power inverter running a sump pump could be the difference that saves a home from flooding. The power to run a heater could save someone thousands of dollars by keeping plumbing pipes from freezing. Also great for emergency backup power applications is the automatic transfer switch on this unit, which keeps the power supply uninterrupted in the event of an outage. With the inverter hooked up to shore power, it will detect the loss of electricity and start pulling energy from a connected battery bank instead to keep the power supply constant.

• 4000 watt low frequency inverter
• 12000 watt surge for 20 seconds 300% surge capability
• Battery priority selector
• AC direct connect terminal bock for hardwire
• Marine coated and protected
• Multi stage smart charger 100 Amp
• Charges lithium LiFePO4, GEL, AGM and lead batteries. We recommend to check battery charging specifications for all batteries.
• Remote panel available
• Auto frequency
• 10msec typical transfer time
• Selectable 25W power save mode (hibernation)
• 7 battery type settings for charger
• Automatic transfer switch

Inverter Output Specifications:

• Continuous Output Power: 4000 Watts
• Surge Rating: 12000 Watts (20 Seconds)
• Output Waveform: Pure Sine/Same as input (Bypass Mode)
• Nominal Efficiency: >88% (Peak)
• Line Mode Efficiency: >95%
• Output Frequency: 50Hz +/- 0.3Hz / 60Hz +/- 0.3Hz
• Typical Transfer Time: 10ms (Max)
• THD: < 10% DC
• Ambient Operating Temperature: 14°F to 122°F (-10°C to 50°C)

Input Specifications

• Nominal Input Voltage: 12.0Vdc
• Minimum Start Voltage: 10.0Vdc
• Low Battery Alarm: 10.5Vdc-11.0Vdc
• Low Battery Trip: 10.0Vdc-10.5Vdc
• High Voltage Shutdown: 16.0Vdc
• Low Battery Voltage Restart: 13.3Vdc
• Idle Consumption: <3.47 amps DC
• Power Saver Mode Idle Consumption: <0.53 amps DC

Charger Specifications

• Output voltage: depends on battery type
• Charger rate: 115A
• Over charge protection shutdown 15.7V
• Selectable charge setting based on battery type
• Adjustable charge current: off-20%-100%
• Four stage smart charger

Transfer Switch Specifications

• 40 amp automatic transfer switch
• 10 ms (max)

Dimensions

• Unit Weight: 64 lbs.
• Unit Size L x W x H: 27.88 x 8.75 x 7.10 inches
• Shipping Weight: 75 lbs.
• Shipping L x W x H 30.5 x 14.25 x 13.75 inches

 

4000 Watt Pure Sine Inverter Charger 12Vdc / 120Vac Input & 120/240Vac Split Phase Output

This 4000 watt inverter charger produces a pure sine wave, which some appliances require for use. So it can run laser jet printers, computers, televisions, CPAP machines and other medical equipment. During a big storm that knocks out electricity, a battery-bank and power inverter running a sump pump could be the difference that saves a home from flooding. The power to run a heater could save someone thousands of dollars by keeping plumbing pipes from freezing. Also great for emergency backup power applications is the automatic transfer switch on this unit, which keeps the power supply uninterrupted in the event of an outage. With the inverter hooked up to shore power, it will detect the loss of electricity and start pulling energy from a connected battery bank instead to keep the power supply constant.

• 4000 watt low frequency inverter
• 12,000 watt surge for 20 seconds 300% surge capability
• 120/240 VAC output Split Phase Charges with 120 Vac multi-stage smart charger
• 115 Amp battery priority selector
• Charges lithium LiFePO4, gel, AGM and lead batteries. We recommend checking battery charging specifications for all batteries.
• Direct connect AC terminal block
• Marine coated and protected
• Remote panel available auto frequency
• 10msec typical transfer time optional 25W power save mode
• 7 battery type settings for charger
• 7 Automatic transfer switch

• Continuous Output Power: 4000 Watts
• Surge Rating: 12,000 Watts (20 Seconds)
• Output 120/240 Vac - Split Phase 60hz
• Output Waveform: Pure Sine/Same as input (Bypass Mode)
• Nominal Efficiency: >88% (Peak) Line Mode Efficiency: >95%
• Output Frequency: 60Hz +/- 0.3Hz
• Typical Transfer Time: 10ms (Max)
• THD: < 10% DC
• Ambient Operating Temperature: 14°F to 122°F (-10°C to 50°C)

Input Specifications

• Nominal Input Voltage: 12.0Vdc
• Minimum Start Voltage: 10.0Vdc
• Low Battery Alarm: 10.5Vdc-11.0Vdc
• Low battery Trip: 10.0Vdc-10.5Vdc
• High Voltage Alarm: 16.0Vdc Low battery
• Voltage Restart: 15.5Vdc
• Idle Consumption: 50 Watts
• Power Saver Mode Idle Consumption: 21 Watts

Charger Specifications

• Output voltage: Depends on battery Type
• Charger Rate: 115A Over
• Charge Protection Shutdown 15.7V
• Selectable Charge setting based on battery type
• Adjustable charge current off-20%-100%
• Four Stage Smart Charger
• Transfer Switch Specifications 40 amp automatic transfer switch 10 ms (max)

Dimensions

• Unit weight: 75 lb
• Unit size: L x W x H: 31.5 x 8.75 x 7.25 inches
• Shipping weight: 87 lb
• Shipping size: L x W x H: 35.5 x 14.50 x 13.50 inches
• Shipping Weight: 75 lbs. Shipping L x W x H 30.5 x 14.5 x 13.75 inches

 

4000 Watt Pure Sine Inverter Charger 12Vdc / 240Vac Input & 120/240Vac Split Phase Output

This 4000 watt inverter charger produces a pure sine wave, which some appliances require for use. So it can run laser jet printers, computers, televisions, CPAP machines and other medical equipment. During a big storm that knocks out electricity, a battery-bank and power inverter running a sump pump could be the difference that saves a home from flooding. The power to run a heater could save someone thousands of dollars by keeping plumbing pipes from freezing. Also great for emergency backup power applications is the automatic transfer switch on this unit, which keeps the power supply uninterrupted in the event of an outage. With the inverter hooked up to shore power, it will detect the loss of electricity and start pulling energy from a connected battery bank instead to keep the power supply constant.

• 4000 watt low frequency inverter
• 12000 watt surge for 20 seconds 300% surge capability
• 120/240 Vac output split phase
• Battery priority selector
• AC direct connect terminal block
• Marine coated and protected
• Multi stage smart charger 115 Amp
• Charges lithium LiFePO4, gel, AGM and lead batteries. We recommend checking battery charging specifications for all batteries.
• Remote panel available
• Auto frequency
• 10msec typical transfer time
• Selectable 25W power save mode (hibernation)
• 7 battery type settings for charger
• Automatic transfer switch

Inverter Output Specifications:

• Continuous Output Power: 4000 Watts
• Surge Rating: 12000 Watts (20 Seconds)
• Output 120/240 Vac - Split Phase 50 or 60hz
• Output Waveform: Pure Sine/Same as input (Bypass Mode)
• Nominal Efficiency: >88% (Peak)
• Line Mode Efficiency: >95%
• Output Frequency: 50Hz +/- 0.3Hz / 60Hz +/- 0.3Hz
• Typical Transfer Time: 10ms (Max)
• THD: < 10% DC
• Ambient Operating Temperature: 14°F to 122°F (-10°C to 50°C)

Input Specifications

• Nominal Input Voltage: 12.0Vdc
• Minimum Start Voltage: 10.0Vdc
• Low Battery Alarm: 10.5Vdc-11.0Vdc
• Low battery Trip: 10.0Vdc-10.5Vdc
• High Voltage Alarm/shutdown: 16.0Vdc
• Low Battery Voltage Restart: 13.3Vdc
• Idle Consumption: 50 Watts
• Power Saver Mode Idle Consumption: 21 Watts

Charger Specifications

• Output voltage: Depends on battery Type
• Charger Rate: 115A
• Over Charge Protection Shutdown 15.7V
• Selectable Charge setting based on battery type
• Adjustable charge current off-20%-100%
• Four Stage Smart Charger

Transfer Switch Specifications

• 40 amp automatic transfer switch
• 10 ms (max)

Dimensions

• Unit Weight: 64 lbs.
• Unit Size L x W x H: 27.88 x 8.5 x 7.0 inches
• Shipping Weight: 75 lbs.
• Shipping L x W x H 30.5 x 14.5 x 13.75 inches

 

AIMS Power 5000 Watt 24 Volt 24 VDC 120 VAC 60Hz Power Inverter PWRINV500024W This 5000 watt 24 Volt DC  power inverter by AIMS Power converts DC (direct current) power stored by batteries into AC (alternating current) electricity that can be used to run practically any household appliances or tools. This unit produces a modified sine wave, which is capable of running most  tools, pumps, motors and appliances. Use this product for off-grid back-up power at home, cabin, boat, larger solar systems or anywhere that doesn't have city power. What really makes this 5000 watt AIMS Power inverter special is its capability to run off at 24 volt DC which allows for more efficiency at higher loads.  This makes the inverter very attractive to users using a 24 volt DC source or multiple batteries. The biggest incentives for using inverters for electricity include the fact that they make little-to-no noise, making for a more peaceful environment for customers, and that they’re non-polluting, which makes for a great green-energy marketing campaign. The unit features two easily-accessible AC outlets with a maximum output of 1500 watts. The 200 percent surge capabilities of this unit should only be used as a safety feature. Other safety features include over-temperature and over-load LED indicators that are used as a warning system for the operator.  Also on the AC side of the unit are the battery voltage and amperage meters which display the usage levels of your battery bank. This inverter is equipped with dual cooling fans and over-temperature protection that keeps it from overheating. Features:

• • 5000W max continuous power
  • Modified sine wave
  • Volt meter on front panel to monitor your battery voltage
  • Amp meter on front panel to monitor your current use (rate at which battery is drained)
  • AC Direct Connect Terminal

• Over Temperature LED indicator
• Over Load LED indicator
• Quadruple ac receptacle that can be used with any separate spliter to provide even more outlets
• On/off switch
• Over Temperature protection
• Over Load protection
• Single cooling fan operation thermally controlled
• Internally fuse protected
• ac output short circuit protection
• Auto reset on most fault conditions
• Aluminum case for optimal cooling
• Pre-wired for remote on/off switch
• Pre-slotted mounting plate
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

Specifications:

• Continuous output power: 5000 Watts
• Surge power capability (peak power): 10,000 Watts
• dc input / operating voltage: 34 to 20 Volts
• Output voltage: 120 Volts ac +/- 10%
• Output wave form: modified sine wave with phase correction
• Output frequency: 60 Hz +/- 1 Hz
• Battery low voltage alarm: 21.0 +/- 0.5 Volts
• Battery low voltage shutdown: 20.0 +/- 0.5 Volts
• No load current @ 24V: < 0.4 Amps
• Full load efficiency: 90%
• 1/3 load efficiency: 95%
• No load minimum operating temperature: -15 degrees Celsius
• Full load maximum operating temperature: 55 +/- 5 degrees Celsius (automatic shutdown)
• No load draw: Switch on - <1 amp DC. Switch off - <.2 mADC
• AC Output Socket Type: quadruple Type 2 -3 prong
• High input voltage protection: 34.5V
• Low input voltage shutdown: 20.0V
• Internal fuse protection
• Product size (L x W x H): 16.92”X 7.95”X 6.1”
• Unit Weight 16.72 lbs
• Boxed Weight 20 lbs
• UL maximum recommended per outlet 1500W

 

AIMS Power 5000 Watt 36 Volt Power Inverter This 5000 watt 36 Volt DC  power inverter by AIMS Power converts DC (direct current) power stored by batteries into AC (alternating current) electricity that can be used to run practically any household appliances or tools. This unit produces a modified sine wave, which is capable of running most tools, pumps, motors and appliances. Use this product for off-grid back-up power at home, cabin, boat, larger solar systems or anywhere that doesn't have city power. What really makes this 5000 watt AIMS Power inverter special is its capability to run off at 36 volt DC which allows for more efficiency at higher loads.  This makes the inverter very attractive to users using a 36 volt DC source or multiple batteries. The biggest incentives for using inverters for electricity include the fact that they make little-to-no noise, making for a more peaceful environment for customers, and that they’re non-polluting, which makes for a great green-energy marketing campaign. The unit features four easily-accessible AC outlets with a maximum output of 1500 watts. The 200 percent surge capabilities of this unit should only be used as a safety feature. Other safety features include over-temperature and over-load LED indicators that are used as a warning system for the operator.  Also on the AC side of the unit are the battery voltage and amperage meters which display the usage levels of your battery bank. This inverter is equipped with dual cooling fans and over-temperature protection that keeps it from overheating. Features

• 5000 Watt max continuous power
• 36 Volt Power Inverter
• Modified sine wave
• Volt meter on front panel to monitor your battery voltage
• Amp meter on front panel to monitor your current use (rate at which battery is drained)
• AC Direct Connect Terminal
• Over Temperature LED indicator
• Over Load LED indicator
• Quadruple ac receptacle that can be used with any separate spliter to provide even more outlets
• On/off switch
• Over Temperature protection
• Over Load protection Single cooling fan operation thermally controlled Internally fuse protected ac output short circuit protection
• Auto reset on most fault conditions
• Aluminum case for optimal cooling
• Pre-wired for remote on/off switch
• Pre-slotted mounting plate
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

Specifications

• Continuous output power: 5000 Watts
• Surge power capability (peak power): 10,000 Watts
• dc input / operating voltage: 30 to 48 Volts
• Output voltage: 120 Volts ac +/- 10%
• Output wave form: modified sine wave with phase correction
• Output frequency: 60 Hz +/- 1 Hz
• Battery low voltage alarm: 31 +/- 0.5 Volts
• Battery low voltage shutdown: 28 +/- 0.5 Volts
• No load current: < 0.9 Amps
• Full load efficiency: 90%
• 1/3 load efficiency: 95%
• No load minimum operating temperature: -15 degrees Celsius
• Full load maximum operating temperature: 55 +/- 5 degrees Celsius (automatic shutdown)
• AC Output Socket Type: quadruple Type 2 -3 prong
• High input voltage protection: 48 volts
• Low input voltage shutdown: 28 volts
• Internal fuse protection
• Product size (L x W x H): 16.92”X 7.95”X 6.10”
• Weight: unit 16.72 lbs boxed 20 lbs
• UL maximum recommended per outlet 1500W

 

AIMS Power 5000 Watt 48 Volt Power Inverter

AIMS Power 5000 Watt Power Inverter 12 Volt 12 VDC 120 VAC 60Hz This 5000-watt 12-volt power inverter by AIMS Power converts DC (direct current) power stored by batteries into AC (alternating current) electricity. You can use this powerful AIMS 5000-watt inverter to run practically any household appliances or tools. This unit produces a modified sine wave capable of running most tools, pumps, motors and appliances. Use this product for off-grid back-up power at home, in your cabin or on your boat. This 5000-watt power inverter is perfect for larger solar systems or anywhere that doesn't have city power. What really makes this 5000-watts power inverter special is its capability to run off most vehicles' standard power systems at 12 volts. That also makes it a simple solution for RVs and boats. This inverter is very attractive to mobile business owners because users don't have to modify a vehicle's standard power system to run the inverter. This will definitely save you some money if you are upgrading a fleet of vehicles with some aftermarket equipment that requires this much power. Some of the popular mobile business applications for this inverter include powering a small mobile office or kitchen, running tools on a work truck or construction vehicle, or supplying electricity to lawn maintenance equipment. One of the biggest incentives for business owners to use inverters for electricity is the fact they make little or no noise. That creates a more peaceful environment for customers and their neighbors. In addition, these inverters are non-polluting. They create no stinky exhaust fumes and can make for a great green-energy marketing campaign. That can be a real boost to your business, especially in competitive markets. This unit features two easily accessible AC outlets with a maximum output of 1500 watts. The 200% surge capabilities of this inverter should only be used as a safety feature. Other safety features include over-temperature and overload LED indicators as a warning system for the operator. Also on the AC side of the unit, you'll find the battery voltage and amperage meters, which display the usage levels of your battery bank. This inverter is equipped with dual cooling fans. Over-temperature protection keeps it from overheating. We offer this product with a one-year parts and labor warranty. It also comes with one year of free tech support. If you need an inverter that produces a pure sine wave, please check out AIMS Power's pure sine wave options. Features

• 5000W max continuous power
• Modified sine wave
• Volt meter on front panel to monitor your battery voltage
• Amp meter on front panel to monitor your current use (rate at which battery is drained)
• AC Direct Connect Terminal!
• Over Temperature LED indicator
• Over Load LED indicator
• Quadruple ac receptacle that can be used with any separate spliter to provide even more outlets
• On/off switch
• Over Temperature protection
• Over Load protection
• Single cooling fan operation thermally controlled
• Internally fuse protected
• ac output short circuit protection
• Auto reset on most fault conditions
• Aluminum case for optimal cooling
• Pre-wired for remote on/off switch
• Pre-slotted mounting plate
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

Specifications:

• Continuous output power: 5000 Watts
• Surge power capability (peak power): 10000 Watts
• dc input / operating voltage: 10 to 15 Volts
• Output voltage: 120 Volts ac +/- 10%
• Output wave form: modified sine wave with phase correction
• Output frequency: 60 Hz +/- 1 Hz
• Battery low voltage alarm: 10.5 +/- 0.5 Volts
• Battery low voltage shutdown: 10.0 +/- 0.5 Volts
• No load current: < 0.6 Amps
• Full load efficiency: 90%
• 1/3 load efficiency: 95%
• No load minimum operating temperature: -15 degrees Celsius
• Full load maximum operating temperature: 55 +/- 5 degrees Celsius (automatic shutdown)
• AC Output Socket Type: quadruple Type 2 -3 prong
• High input voltage protection: 15V-17V
• Low input voltage shutdown: 10V
• Internal fuse protection
• Product size (L x W x H): 16.92”X 7.95”X 6.1”
• Weight: unit 18 lbs boxed 20 lbs
• UL maximum recommended per outlet 1500W

 

AIMS Power 5000 Watt Power Inverter 12Vdc to 240Vac 60Hz 12 VDC 240 VAC 60Hz This 5000 watt 12 volt DC to 220/230/240 volt AC (60 hz)  power inverter by AIMS Power converts DC (direct current) power stored by batteries into AC (alternating current) electricity that can be used to run practically any household appliances or tools. This inverter will NOT product 120 volts. It is only for 240 volt AC applications. See PWRINV500012W for applications needing 120 volt AC. This unit produces a modified sine wave, which is capable of running most  tools, pumps, motors and appliances that operate at 240 volts AC. Use this product for off-grid back-up power at home, cabin, boat, larger solar systems or anywhere that doesn't have city power. What really makes this 5000 watt AIMS Power inverter special is its capability to run off of most vehicles’ and/or RVs'/boats' standard power systems at 12 volts. That makes the inverter very attractive to mobile business owners since users don’t have to modify a vehicle’s standard power system in order to run the inverter off of a car or truck. This definitely saves some money if upgrading a fleet of vehicles with some aftermarket equipment that requires this much power. Some of the popular mobile business applications include powering a small mobile office or kitchen, running tools on a work truck or construction vehicle, or supplying electricity to lawn maintenance equipment. The biggest incentives for business owners to use inverters for electricity include the fact that they make little-to-no noise, making for a more peaceful environment for customers, and that they’re non-polluting, which makes for a great green-energy marketing campaign. The unit features two easily-accessible AC outlets with a maximum output of 1500 watts. The 200 percent surge capabilities of this unit should only be used as a safety feature. Other safety features include over-temperature and over-load LED indicators that are used as a warning system for the operator.  Also on the AC side of the unit are the battery voltage and amperage meters which display the usage levels of your battery bank. This inverter is equipped with dual cooling fans and over-temperature protection that keeps it from overheating. If an inverter that produces a pure sine wave is needed, please check out AIMS Power’s pure sine wave options. Features

• 5000W max continuous power
• Modified sine wave
• 240 Volt single phase AC output only. This inverter will not deliver 120 volt AC.
• Volt meter on front panel to monitor your battery voltage
• Amp meter on front panel to monitor your current use (rate at which battery is drained)
• AC Direct Connect Terminal
• Over Temperature LED indicator
• Over Load LED indicator
• Dual 240V AC Receptacles
• On/off switch
• Over Temperature protection
• Over Load protection
• Single cooling fan operation thermally controlled
• Internally fuse protected
• AC output short circuit protection
• Auto reset on most fault conditions
• Aluminum case for optimal cooling
• Pre-wired for remote on/off switch
• Pre-slotted mounting plate
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

Specifications:

• Continuous output power: 5000 Watts
• Surge power capability (peak power): 10,000 Watts
• dc input / operating voltage: 10 to 15 Volts
• Output voltage: 240 Volts ac
• Output frequency: 60 Hz +/- .5 Hz
• Battery low voltage alarm: 10.5 +/- 0.5 Volts
• Battery low voltage shutdown: 10.0 +/- 0.5 Volts
• No load minimum operating temperature: -15 degrees Celsius
• Full load maximum operating temperature: 55 +/- 5 degrees Celsius (automatic shutdown)
• Low voltage and over voltage alarm and protection
• AC Output Socket Type: dual 240
• Low input voltage shutdown: 10V
• Internal fuse protection
• Product size (L x W x H): 16.92 X 7.95 X 6.1 inches
• Weight: Unit - 16.72 lbs Boxed - 20 lbs

 

5000 Watt Pure Sine Inverter - 12 volt 50/60 hz Industrial

AIMS Power is proud to bring you this new 5000-Watt Pure Sine Power Inverter. Designed for harsh environments, it has been completely overhauled. This AIMS 5000-watt inverter now boasts a dual GFCI outlet and is FCC certified. This product also includes a thermally controlled fan, meaning it delivers increased efficiency with less noise. It will continue to put out stable, pure sine power and maintain output voltage even as your battery bank voltage decreases. High-output performance is achieved through a DSP (Digital Signal Process) drive. With this 5000-watt power inverter, 12-volt industrial-grade design provides power and flexibility for business or pleasure. This inverter is ideal for running nonlinear loads (such as variable-speed motors and small compressors). Pure sine power is also preferred for laser jet printers, sensitive electronics and computer servers as well as microwaves, medical equipment, anything with a circuit board and cordless drill battery chargers. An external battery voltage sensor lets you monitor your battery capacity and power consumption. Packed with 5000 watts of power, this inverter can be used for off-grid home backup power systems. It's ideal for solar and boat applications as well as work vehicles and RVs. It can help give you the ability to work or play practically anywhere. We back it with a one-year warranty on parts and labor as well as free lifetime tech support. Features

• 5000 Watt continuous power
• 10000 Watt surge
• 12 Volt DC input
• Pure sine wave
• 60hz or 50hz switch
• Highly efficient : > 95% @ 1/3 load
• Efficient output at low voltage
• 2 - GFCI Dual Outlet
• Direct connect AC Terminal Block Connector and
• Cable for optional remote on/off switch
• Isolated ground & neutral
• Short circuit protection (GFCI and
• AC Breaker)
• On/off switch
• 5 Function Protection LED indicator
• AC Breaker
• Dual cooling fans thermally controlled
• DC volt meter included
• Instruction manual
• Lifetime tech support
• 1 Year Warranty Parts and Labor replacement

Specifications

• DC Input Voltage 13.2 V (10.5V-15V)
• Output Voltage no load 120Vac +/- 3%
• Continuous 5000 Watts
• Surge 10000 Watts (1/2 second)
• 91% Efficiency @ full load
• No Load Current (Fan Off) 2.6A 12V
• No Load Current (Fan On) 4.4A 12V
• Low Battery Shut Down: 10.0V
• Low Battery Return on Power: 11.2V
• High Battery Shut Down: 15.9V
• High battery return on Power: 15.0V
• Frequency Selection 50/60hz
• Over Temperature Protection: -25ºC - 79ºC
• Cooling Fan on Temperature: 40ºC
• GFCI Outlets rated at 20A per block.
• Dimensions (inches) 23.75 x 8.88 x 6.25
• Weight: 27lbs

 

600 Watt Pure Sine Inverter Charger 12V ETL Listed to UL 458

This 600 watt pure sine inverter charger ETL listed and conforms to UL 458 standards, is a combination of an inverter, battery charger and AC auto-transfer switch into one complete system with a peak DC and AC conversion efficiency of 80%. It is packed with unique features and it is one of the most advanced inverter chargers in the market today. It features power factor corrected, sophisticated multi-stage charging and pure sine wave output with unprecedentedly high surge capability to meet demanding power needs of inductive loads without endangering the equipment. The AC/Battery priority and auto generator start functionality make it suitable to work in either backup power or renewable energy applications. When customized to Battery priority mode via a DIP switch, the inverter will extract maximum power from external sources and renewable energy systems, with only minimal battery cycles being required. The overloads capacity is 300% of continuous output for up to 20 seconds to reliably support tools and equipment longer. In AC priority mode, when utility AC power cuts off, the transfer relay is de-energized and the load is automatically transferred to the inverter output. Once the qualified AC utility is restored, the relay is energized and the load is automatically transferred to AC utility. When switching to battery priority mode via the DIP switch, the inverter will extract power from external power sources in renewable energy systems and a minimal cycle of the battery will be required. With the availability of the auto generator start, an electrical generator can be integrated into the system as a backup and started when the battery voltage goes low.

• 600 watt low frequency inverter - ETL listed to UL 458 standards
• 1800 watt surge for 20 seconds 300% surge capability
• AC Input Cable
• GFCI outlet
• Conformal Coated for Marine Applications
• Multi Stage Smart Charger 20 Amp charges GEL, Lead, AGM, Lithium
• Remote Panel Available
• Auto Frequency Detect From AC Input
• Less than 10msec Typical Transfer Time
• Selectable 25W power save mode (hibernation)
• 7 Battery Type Settings for Charger
• Automatic transfer switch

• Continuous Output Power: 600 Watts
• Surge Rating: 1800 Watts (20 Seconds)
• Output Waveform: Pure Sine/Same as input (Bypass Mode)
• Output Voltage: 120Vac
• Nominal Efficiency: 80% (Peak)
• Line Mode Efficiency: >95%
• Output Frequency: 50Hz ± 0.3Hz / 60Hz ± 0.3Hz
• Typical Transfer Time: 10ms (Max)
• THD: <10%

Input Specifications:

• Nominal Input Voltage: 12.0Vdc
• Minimum Start Voltage: 10.0Vdc
• Low Battery Alarm: 10.5Vdc-11.0Vdc
• Low Battery Trip: 10.0Vdc-10.5Vdc
• High Voltage Alarm: 16.0Vdc
• Low Battery Voltage Restart: 13.3Vdc
• Low Batter Voltage Recover: 13.0Vdc
• Idle Consumption: <<25W - depending on search mode

Charger Specifications:

• Output Voltage: Depends on battery Type
• Charger Rate: 20A
• Over Charge Protection Shutdown: 15.7V
• Selectable Charge setting based on battery type
• Adjustable charge current off-20%-100%
• Four Stage Smart Charger
• Bypass: 7amps
• Low voltage trip: 8090V +/-4%
• Low voltage trip: 90100V +/-4%
• High voltage trip: 140V +/-4%
• High voltage re engage: 135V +/-4%
• Max input AC voltage: 150

Dimensions:

• Unit Weight: 18 lbs.
• Unit Size L x W x H: 14.75 x 7 x 5.5 inches
• Shipping Weight: 20 lbs.
• Shipping L x W x H: 17 x 9.75 x 8.5 inches

 

600 Watt Pure Sine Power Inverter 12 Volt Listed to UL 458

Power inverters have become a staple in businesses and homes around the world due to intermittent brown and black-outs. AIMS Pure Sine Wave Power Inverters provide reliable transformation of DC power from a battery (such as the one in a car or RV) into AC power that can then be used to run lights computers printers televisions medical equipment* and a broad range of appliances. And when it comes to selecting an inverter it's helpful to know that AIMS Pure Sine Wave inverters represent the most technologically advanced lightweight compact and diverse inverters on the market to help ensure the widest use of applications. For over a decade the AIMS Power Pure Sine Wave Power Inverters has consistently delivered the broadest range of sizes to accommodate virtually every power requirement. Advantages of a pure sine inverter:

• Equipment runs more efficiently
• Motors run cooler
• Cleaner power
• Ideal for power tool chargers laser printers electric shavers microwaves variable speed motors TV's medical equipment

To select the right inverter first determine what devices you would need to run in the event of a power outage. Then select the appropriate inverter that can carry the combined wattage requirements of these devices. Please see our tech support section for start up averages for all devices. At AIMS you'll discover our inverters range from 100 watts up to 12,000 watts more than enough to power nearly every application imaginable. Features:

• 600W continuous power
• Pure sine wave
• Listed to UL 458 and CSA 22.2 standards
• USB Port
• Optional remote port
• Dual AC receptacle
• On/off switch
• Over temperature indicator
• Overload protection
• Low battery voltage warning/shutdown
• Alligator clips included 28"
• High input voltage protection with automatic shutdown
• Over load indicator
• Short circuit protection
• Load based fan - only runs when an inverter senses a certain load
• Enclosed dc battery connections
• AC output short circuit protection
• Instruction manual
• Free 2 year tech support
• 2 Year Warranty Parts and Labor

Specifications:

• Continuous output power: 600 Watts
• Surge power capability (peak power): 1200 Watts
• DC input / operating voltage: 10 to 15 Volts
• Output voltage: 120 Volts ac
• Output voltage regulation: +/- 3%
• Output wave form: pure sine wave
• Output frequency: 60 Hz
• Battery low voltage alarm: 10.6 +/- 0.5 Volts
• Battery low voltage shutdown: 10.0 +/- 0.5 Volts
• Low battery voltage warning/shutdown
• No load power consumption: < .6 dc amps
• DC amps - 50
• AC amps - 5
• Full load efficiency: 85%
• 1/3 load efficiency: >90%
• No load minimum operating temperature: 32 degrees F
• Full load maximum operating temperature: 104 degrees F (automatic shutdown)
• AC Output Socket Type: dual Type 2 -3 prong and USB Output
• High input voltage protection: 15V
• Low input voltage shutdown: 10V
• Internal blade fuse protection
• Product size (L x W x H): 8.39" x 5.51" x 2.91"
• Weight: Unit: 3.68 Boxed: 5.0

 

AIMS Power 7000 Watt Power Inverter 24VDC to 240VAC Industrial Grade 50/60 Hz At 7000 watts and up to 14,000 watts for 9 seconds, 24 VDC the Industrial Grade Modified Sine Wave Power Inverter promises to be a complete solution for any power need you present. From recreation to industrial applications or off-grid home and solar power needs, this 7000 watt modified sine wave inverter delivers enough durable power for high end equipment that requires substantial electricity powering items that require 240 VAC. It's rugged design is great for high vibration environments and operates in extreme temperatures.This digitally outputted and phase corrected inverter is the recommended power solution for clean reliable output without noise or distortion. Delivering an incredible 7000 watts of continuous power this utility-grade inverter was designed to reproduce the quality of electricity provided by power companies to create a stable AC power source. This inverter supplies ample power to run large pumps compressors power tools multiple appliances job sites and even a small house! It has PWM programming which corrects any fluctuation in voltage or frequency caused by battery fluctuation or sudden surges in power usage. It also has a longer than average surge time (9 seconds when over 7000 watts). **Single phase only. It does NOT put out 2 legs of 120 V. Features:

• 7000W max continuous power
• Modified sine wave
• Select-able frequency switch for 50 Hz or 60 Hz
• Power switch LED is also a self test light - Green
• Overload fail LED - Red
• Over Temperature LED indicator
• Over Load LED indicator
• 1 AC receptacles 240 volt
• Direct connect terminal block for full load applications
• On/off switch
• Over Temperature protection
• Over Load protection
• Thermally controlled fan
• Percent load usage LED bar
• Externally located re-settable circuit breakers
• ac output short circuit protection
• Aluminum case for optimal cooling
• Pre-wired for remote on/off switch
• Pre-slotted mounting plate
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

Specifications:

• Continuous output power: 7000 Watts
• Surge power capability (peak power): 14000 Watts

The surge duration is electronically controlled and permits up to 9 seconds while the output is between 7000 and 14000 watts. During this time the buzzer will sound until the inverter electronically shuts down.

• dc input / operating voltage: 20-30 Volts
• Output voltage: 247 Volts ac +/- 10%
• Output wave form: modified sine wave with phase correction
• Output frequency: 50/60 Hz +/- 1 Hz
• Battery low voltage alarm: 20 +/- 0.5 Volts
• Battery low voltage shutdown: 19.5 +/- 0.5 volts
• High input voltage protection 34 +/-0.5 volts
• No load current: 200mA
• Start up AC amps: 58
• Continuous AC amps: 29
• Full load efficiency: 90%
• Auto Cooling Fan Start at 107 degrees F
• Full load maximum operating temperature: 163 degree F
• AC Output Socket Type: single 240 volt plug
• Internal fuse protection
• Product size (D x W x H): 21.26” X 8.43” X 5.35”
• Weight: 26.5 lbs

 

AIMS Power 7000 Watt Power Inverter 48Vdc to 240Vac Industrial Grade 50/60 hz

AIMS Power 800 Watt Power Inverter with Cables 12 VDC 120 VAC 60Hz Overview: Modified Sine Wave Power Inverters represent the most economical solution for powering a large number of appliances. The waveform produced by a Modified Sine Wave Power Inverter is “blocky” resembling a set of steps whereas the waveform produced by utility companies is smooth much like a curvy road. Therefore because of the type of waveform the Modified Sine Wave Power Inverters produce they are suitable for most applications. Modified Sine Wave Power Inverters are more efficient in converting battery power to AC. So if you’re looking to make a pot of coffee run a heater or air conditioner or appliances that can withstand occasional electrical noise a Modified Sine Wave Inverter is a cost-effective solution. To select the right inverter first determine what devices you would need to run in the event of a power outage. Then select the appropriate inverter that can carry the combined wattage requirements of these devices. Some appliances have a start up amperage. At AIMS you’ll discover our inverters range from 75 watts up to 8000 watts – more than enough to power nearly every application imaginable. Features:

• 800 watt continuous power
• Modified sine wave
• LED: Green power on and red heavy load/fault condition
• Dual ac receptacle
• On/off switch
• Over Temperature protection
• Over Load protection
• Convenient cooling fan operation
• Cables included for direct connect to battery. 40" 8 awg.
• Internally fuse protected
• ac output short circuit protection
• Aluminum case for optimal cooling
• Pre-slotted mounting plate
• Isolated ground neutral
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

Specifications:

• Continuous output power: 800 Watts
• Surge power capability (peak power): 1600 Watts not meant for start up applications
• Short circuit protection
• dc input / operating voltage: 10 to 15 Volts · Output voltage: 120 Volts ac
• Output wave form: modified sine wave
• Output frequency: 60 Hz
• Battery low voltage alarm: 10.5 +/- 0.5 Volts
• Battery low voltage shutdown: 10.0 +/- 0.5 Volts
• No load current @ 12V: < 0.7 dc Amps
• Full load efficiency: 90%
• 1/3 load efficiency: 95%
• No load minimum operating temperature: -15 degrees Celsius
• Full load maximum operating temperature: 55 +/- 5 degrees Celsius (automatic shutdown)
• AC Output Socket Type: dual Type 2 -3 prong
• High input voltage protection: 15.5V
• Low input voltage shutdown: 10.5V
• Internal fuse protection
• Product size (L x W x H): 9.25”X 3.5”X 2.25”
• Unit Weight: 2.6 lbs
• Boxed Weight: 4.0 lbs

 

AIMS Power 8000 Watt Modified Sine Inverter 12 VDC 240 VAC 60Hz Our 8000-Watt Modified Sine Inverter delivers inverter technology at its finest. This exciting new 8000W 12V modified sine inverter is smaller, lighter, and more efficient. AIMS Power's old model of this inverter is still trusted and will continue to be used long into the future by business owners around the world, including mobile businesses. But we have developed a new version of this 8000-watt inverter that's even better. Thanks to advances in technology, this redesigned inverter will be in high demand. Weighing just under 20 pounds, our new AIMS Power 8000-watt DC to AC power inverter measures 19.02" x 7.76" x 6.02". Its ability to run off most vehicles' and RV and boat 12-volt power systems makes it an ideal solution for owners of mobile businesses. You can run the inverter from most car and truck systems without having to modify the power source.

• 8000W max continuous power
• Modified sine wave
• Volt meter on front panel to monitor your battery voltage
• Amp meter on front panel to monitor your current use (rate at which battery is drained)
• Over Temperature LED indicator
• Over Load LED indicator
• AC direct connect terminal block
• On/off switch
• Over Temperature protection
• Over Load protection
• Single cooling fan thermally controlled
• Internally fuse protected
• AC output short circuit protection
• Auto reset on most fault conditions
• Aluminum case for optimal cooling
• Pre-wired for remote on/off switch
• Pre-slotted mounting plate
• Instruction manual
• Free 1 year tech support
• 1 Year Warranty Parts and Labor

• Continuous output power: 8000 Watts
• Surge power capability (peak power): 16000 Watts
• dc input / operating voltage: 10 to 15 Volts
• Output voltage: 120 Volts ac +/- 10%
• Output wave form: modified sine wave with phase correction
• Output frequency: 60 Hz +/- 1 Hz
• Battery low voltage alarm: 10.5 +/- 0.5 Volts
• Battery low voltage shutdown: 10.0 +/- 0.5 Volts
• No load current: < 1.3 DC amps
• Full load efficiency: 90%
• 1/3 load efficiency: 95%
• No load minimum operating temperature: 30ºF
• Full load maximum operating temperature: 140ºF
• AC Output Socket Type: quadruple Type 2 -3 prong
• High input voltage protection: 15V-17V
• Low input voltage shutdown: 10V Internal fuse protection
• Product size (L x W x H): 19.02"X 7.76"X 6.02"
• Weight: unit 19.8 lbs boxed 24 lbs
• UL maximum recommended per outlet 1500W
• This inverter requires 2 sets of 4 AWT cable if you are going to run at 8000 watts.

 

AIMS Power Ignition or Toggle Relay Switch The AIMS Power ignition/toggle relay switch allows an inverter to be powered using the vehicle's ignition or any trigger switch. Compatible with AIMS Power inverters only. NOT compatible with AIMS Power's inverter chargers. You may use a trigger switch using ports B and C per diagram.

• Compatible with 12, 24, 36 or 48 Volt DC
• RJ9 cable included for connection to inverter - if you need a longer cable, you may extend up to 15ft
• 3 1/4" W x 3" L x 1 1/4" H
• One year warranty
• 10 oz
• Includes mounting screws

*Recommended wire size: 18 AWG  

AIMS Power Remote On/Off Switch REMOTEHF The perfect accessory for your AIMS Power Inverter, This newly designed remote is a flush mountable design making for clean and simple installation. This remote also now features a dip switch allowing you to turn on or off the LED indicator light. Mount this remote to your dash, control panel, or access panel for quick and easy control of your AIMS Power inverter. Includes a 30 foot cord This remote is compatible with the following newly purchased models:

• PWRI100012S
• PIC100012120S
• PWRIX120012S
• PWRIX120012SUL
• PWRIX200012SUL
• PWRINV1250W
• PWRI150012S
• PWRI150024S
• PWRI150048S
• PWRINV200012W
• PWRI200012120S
• PWRINV250012W
• PWRINV250024W
• PWRI300012120S
• PWRINV500012W
• PWRINV500024W
• PWRINV500036W
• PWRINV500048W
• PWRINV5K24012W
• PWRI5K22050
• PWRINV8KW12V
• PWRI8K22050
• PWRINV10KW12V
• PWRINV12KW24V

*If your inverter is over 1 year old please contact sales to determine if the correct remote for your model is still available. Features:

• 30 feet of cable; Easily extendable with standard RJ-9 cable
• Dip Switch for controlling LED indicator lights

Specifications: Dimensions L x W x H: 3 x 2 x 1 inches  

The DSEBC1205 is designed to be permanently connected to a battery, to ensure it maintains a full charge. The charger includes LED indicators on the front that show when there is no battery connected and if a fault condition is present. The chargers continue to operate during cranking & running and have been designed to accept multiple AC voltage connections. The robust design makes the charger ideally suited to a wide range of markets including heavy and light industrial environments. VERTICAL MOUNT 50 mm x 129.6 mm x 138.5 mm 2.0” x 5.1” x 5.45”) HORIZONTAL MOUNT 129.6 mm x 138.5 mm x 50 mm (5.1” x 5.45” x 2.0”) WEIGHT 0.3kg PRODUCT VARIANTS BC1205-01 - 12 Volt 5 Amp Battery Charger

AC SUPPLY

FREQUENCY RANGE 45 Hz to 65 Hz VOLTAGE RANGE 90 V to 305 V (L-N)

DC OUTPUT

5 A DC 12 V DC RIPPLE AND NOISE <3% EFFICIENCY >80%

REGULATION

LINE <1% LOAD <4%

PROTECTIONS

Short Circuit Reverse Polarity  

The DSEBC1205 is designed to be permanently connected to a battery, to ensure it maintains a full charge. The charger includes LED indicators on the front that show when there is no battery connected and if a fault condition is present. The chargers continue to operate during cranking & running and have been designed to accept multiple AC voltage connections. The robust design makes the charger ideally suited to a wide range of markets including heavy and light industrial environments. VERTICAL MOUNT 50 mm x 129.6 mm x 138.5 mm 2.0” x 5.1” x 5.45”) HORIZONTAL MOUNT 129.6 mm x 138.5 mm x 50 mm (5.1” x 5.45” x 2.0”) WEIGHT 0.3kg PRODUCT VARIANTS BC2405-01 - 24 Volt 5 Amp Battery Charger

AC SUPPLY

FREQUENCY RANGE 45 Hz to 65 Hz VOLTAGE RANGE 90 V to 305 V (L-N)

DC OUTPUT

5 A DC 24 V DC RIPPLE AND NOISE <3% EFFICIENCY >80%

REGULATION

LINE <1% LOAD <4%

PROTECTIONS

Short Circuit Reverse Polarity  

The DSEBC2410Ei is an enclosed intelligent battery charger designed to work with multiple battery types across a wide range of applications. The advanced technology has been developed to automatically detect system settings and charging profiles including cell voltage and boost voltage to provide high-levels of charging support. Additional high-level features include external system integration via Modbus RS485, remote temperature compensation, short-circuit and reverse polarity protection, multi-stage charging regimes, configurable charging curves and battery life optimization. NFPA 110 (QWIR) COMPLIANT / UL LISTED OVERALL SIZE 170 mm x 305 mm x 116 mm (6.7” x 12.0” x 4.6”) WEIGHT 2.3kg PRODUCT VARIANTS BC2410Ei-01 - 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display) BC2410Ei-02 - 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display & Meters) BC2410Ei-03 - 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Meters)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT RATING

10 A DC at 12 & 24 V DC RIPPLE AND NOISE <1% EFFICIENCY >86% REGULATION

The DSEBC2410Ei is an enclosed intelligent battery charger designed to work with multiple battery types across a wide range of applications. The advanced technology has been developed to automatically detect system settings and charging profiles including cell voltage and boost voltage to provide high-levels of charging support. Additional high-level features include external system integration via Modbus RS485, remote temperature compensation, short-circuit and reverse polarity protection, multi-stage charging regimes, configurable charging curves and battery life optimization. NFPA 110 (QWIR) COMPLIANT / UL LISTED OVERALL SIZE 170 mm x 305 mm x 116 mm (6.7” x 12.0” x 4.6”) WEIGHT 2.3kg PRODUCT VARIANTS BC2410Ei-01 - 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display) BC2410Ei-02 - 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display & Meters) BC2410Ei-03 - 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Meters)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT RATING

10 A DC at 12 & 24 V DC RIPPLE AND NOISE <1% EFFICIENCY >86% REGULATION

The DSEBC2410Ei is an enclosed intelligent battery charger designed to work with multiple battery types across a wide range of applications. The advanced technology has been developed to automatically detect system settings and charging profiles including cell voltage and boost voltage to provide high-levels of charging support. Additional high-level features include external system integration via Modbus RS485, remote temperature compensation, short-circuit and reverse polarity protection, multi-stage charging regimes, configurable charging curves and battery life optimization. NFPA 110 (QWIR) COMPLIANT / UL LISTED OVERALL SIZE 170 mm x 305 mm x 116 mm (6.7” x 12.0” x 4.6”) WEIGHT 2.3kg PRODUCT VARIANTS BC2410Ei-01 - 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display) BC2410Ei-02 - 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display & Meters) BC2410Ei-03 - 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Meters)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT RATING

10 A DC at 12 & 24 V DC RIPPLE AND NOISE <1% EFFICIENCY >86% REGULATION

The DSEBC2415i is an intelligent 24 volt, 15 amp switch-mode battery charger that can be programmed for different charging curves. This helps to maximise battery life. The charger is programmed using the DSE Configuration Suite Software. The charger can be Chassis or DIN Rail mounted and has three built-in LED's to indicate current charging status and fault conditions. The charger continues to operate during cranking and running and accepts multiple AC voltage connections. OVERALL SIZE 80 mm x 205 mm x 135 mm (3.1" x 8.1" x 5.3") WEIGHT 0.88 kg PRODUCT VARIANTS BC2415i-01 - 24 volt 15 amp Intelligent Battery Charger (90-305v 50/60Hz)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT

DC OUTPUT 15 A DC 24 V DC RIPPLE AND NOISE 1% EFFICIENCY >90%

REGULATION

LINE <0.5% LOAD 2%

TEMPERATURE SENSOR INPUT

PT1000

PROTECTIONS

Short Circuit DC Over Voltage DC Over Current Reverse Polarity Over Temperature AC Under & Over Voltage

CHARGE FAILURE RELAY

3 A 30 V DC volt free relay  

Set of 3 coded AMP SEAL connectors complete with crimps/contacts. MATERIAL Glass reinforced PBT COLOUR Black (A), Grey (B), Black (C) PROTECTION IP67 WEIGHT 0.4 kg/14 oz  

DT16 Deutsch Connector C, 18-way complete with pins. DESCRIPTION DT16 Deutsch connector A, 18-way complete with pins. DT16-18SC-K004 0462-201-16 crimp (x17) 0462-209-16 crimp (x1) MATERIAL Connector - Plastic COLOUR Connector  - Black PROTECTION IP68 TEMPERATURE RATING -55 ˚C to +125 ˚C -67 ˚F to +257 ˚F  

The PCAN-USB adapter enables simple connection to CAN networks. Its compact plastic casing makes it suitable for mobile applications. The opto-decoupled version guarantees galvanic isolation of up to 500 Volts between the PC and the CAN side. The package is also supplied with the CAN monitor PCAN-View for Windows® and the programming interface PCAN-Basic.

KEY FEATURES

• Adapter for USB connection (Full speed mode - USB 1.1 / USB 2.0 / USB 3.0 compatible).
• High-speed CAN connection (ISO 11898-2)
• Bit rates from 5 kbit/s up to 1 Bit/s
• Compliant with CAN specifications 2.0 A and 2.0 B.
• CANbus connection via D-sub - 9 pin
• NXP SJA1000 CAN controller - 16 MHz clock frequency
• NXP PCA82C251 CAN transceiver
• Galvanic isolation on the CAN connection up to 500 V
• CAN termination can be activated through a solder jumpe
• 5-volt supply to the CAN connection can be connected through a solder jumper
• Voltage supply via USB