**Please Note: The DSE9255 has been discontinued. If ordered, you may receive the DSE9255 until stock is depleted or the DSE BC2405 will be the direct replacement** The DSE9255 24 volt 5 amp Switch-Mode Battery Charger keeps batteries charged to their maximum capacity at all times. It is designed for permanent battery connection and can be DIN rail or chassis mounted. The charger includes a normal or overload condition LED indicator on the front to assist with status identification, operates during cranking and running and accepts multiple AC voltage connections. OVERALL SIZE 136 mm x 140 mm x 63 mm (5.4” x 5.5” x 2.5”) WEIGHT 0.5kg PRODUCT VARIANTS 9255-00 – 24 volt 5 amp Compact Battery Charger (90-305v 50/60Hz)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) DC OUTPUT 5 A DC 24 V DC at 13.7 V DC

RIPPLE AND NOISE

<1%

EFFICIENCY

>80%

REGULATION

LINE <0.001% Vo LOAD 1% Vo

PROTECTIONS

Short Circuit Over Voltage Over Current Reverse Polarity  

**Please Note: The DSE9461 has been discontinued and is no longer available.  The recommended replacement battery charger BC2410Ei has a few options:

• BC2410Ei-01 – 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display)
• BC2410Ei-02 – 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display & Meters)
• BC2410Ei-03 – 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Meters)

The DSE9461 is an intelligent enclosed battery charger that has been developed to offer the highest levels of safety, usability and battery life and performance. The charger can be used straight out of the box or connected to a PC via a USB cable to modify the pre-set charging curves. The charging curve can be selected from the PC software or user created for advanced battery applications. The charger can be used as a power supply and includes a high number of input/output protections as standard. The charger also has the ability to connect to an external system via MODBUS RTU, using RS485. OVERALL SIZE 165 mm x 305 mm x 110 mm (6.5″ x 12.0″ x 4.3″) WEIGHT 2.3kg PRODUCT VARIANTS 9461-01 -12 volt 10 amp Enclosed Intelligent Battery Charger (Display) 9461-02 -12 volt 10 amp Enclosed Intelligent Battery Charger (Display & Meters) 9461-11 -24 volt 10 amp Enclosed Intelligent Battery Charger (Display) 9461-12 -24 volt 10 amp Enclosed Intelligent Battery Charger (Display & Meters)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT RATING

10 A DC at 12 & 24 V DC RIPPLE AND NOISE <1% EFFICIENCY >86% AUXILIARY OUTPUT 100 mA DC at 12 V

**Please Note: The DSE9461 has been discontinued and is no longer available.  The recommended replacement battery charger BC2410Ei has a few options:

• BC2410Ei-01 – 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display)
• BC2410Ei-02 – 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Display & Meters)
• BC2410Ei-03 – 12/24 Volt 10 Amp Enclosed Intelligent Battery Charger (Meters)

The DSE9461 is an intelligent enclosed battery charger that has been developed to offer the highest levels of safety, usability and battery life and performance. The charger can be used straight out of the box or connected to a PC via a USB cable to modify the pre-set charging curves. The charging curve can be selected from the PC software or user created for advanced battery applications. The charger can be used as a power supply and includes a high number of input/output protections as standard. The charger also has the ability to connect to an external system via MODBUS RTU, using RS485. OVERALL SIZE 165 mm x 305 mm x 110 mm (6.5″ x 12.0″ x 4.3″) WEIGHT 2.3kg PRODUCT VARIANTS 9461-01 -12 volt 10 amp Enclosed Intelligent Battery Charger (Display) 9461-02 -12 volt 10 amp Enclosed Intelligent Battery Charger (Display & Meters) 9461-11 -24 volt 10 amp Enclosed Intelligent Battery Charger (Display) 9461-12 -24 volt 10 amp Enclosed Intelligent Battery Charger (Display & Meters)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT RATING

10 A DC at 12 & 24 V DC RIPPLE AND NOISE <1% EFFICIENCY >86% AUXILIARY OUTPUT 100 mA DC at 12 V

**Please Note: The DSE9462 Dual Battery Charger has been discontinued and is no longer available.  DSE does not have a “Dual” charger as a direct replacement; however you can choose your replacement by your amps/voltage. For 12/24 Volt, 10 Amp use: BC2410Ei (Meters) BC2410Ei (Display) BC2410Ei (Display & Meters) For 12/24 Volt, 15 Amp use: BC2415Ei Our Multiple Output Chargers have been developed to provide intelligent, lightweight charging for use on-board standby vehicles and systems that use multiple applications or loads. Chargers within the range can be configured to provide different output levels and programmed for optimum performance with different charging curves to maximise the life of the battery. The DSE9462 is configured using the DSE Configuration Suite software via a USB connection. The charger is mounted to a chassis using the fixing holes that are built into the case. The charger’s stylish design includes four coloured LEDs to indicate charging status and fault conditions. For added durability, reliability and silent operation the charger utilises solid state technology with no moving parts. OVERALL SIZE 290 mm x 157 mm x 67 mm (9.4″ x 10.4 ” x 3.5″) WEIGHT 1.8kg PRODUCT VARIANTS 9462-01 – 24 Volt 15 Amp & 12 Volt 10 Amp Dual Output Intelligent Battery Charger (90-305v)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT RATING

CHANNEL 1 15 A DC at 24 V DC CHANNEL 2 10 A DC at 12 V DC RIPPLE AND NOISE 2% x Vo EFFICIENCY AND POWER FACTOR >90% at 0.9pf

REGULATION

The DSE9470 MKII is a UL recognised intelligent switch-mode battery charger that can be programmed for different charging curves. This helps to maximise battery life. The charger is programmed using the DSE Configuration Suite Software. The charger can be DIN rail or chassis mounted and has three built-in LEDs to indicate current charging status and fault conditions. The charger continues to operate during cranking and running and accepts multiple AC voltage connections. OVERALL SIZE 70 mm x 200 mm x 130 mm (2.7” x 7.9” x 5.1”) WEIGHT 0.75kg PRODUCT VARIANTS 9470-01 - 24 V 10 A Intelligent Battery Charger (USA - UL - 110 V - 250 V) 9470-A4 - 24 V 10 A Intelligent Battery Charger (USA & Canada - UL - 110 V - 150 V)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT

DSE9470 OUTPUT 10 A DC at 24 V DC RIPPLE AND NOISE <1% EFFICIENCY >86%

REGULATION

LINE <0.5% LOAD 2%

TEMPERATURE SENSOR INPUT

PT1000

PROTECTIONS

Short Circuit DC Over Voltage DC Over Current Reverse Polarity Over Temperature AC Under & Over Voltage

CHARGE FAILURE RELAY

3 A at 30 V DC volt free relay  

***Please Note: Part Number Change – The DSE9473-01 has been REBRANDED to the BC2415I-01***  Back Order status, Lead Time approximately 4-6 weeks from order date. The DSE9473 is an intelligent 24 volt, 15 amp switch-mode battery charger that can be programmed for different charging curves. This helps to maximize battery life. The charger is programmed using the DSE Configuration Suite Software. The charger can be Chassis or DIN Rail mounted and has three built-in LED’s to indicate current charging status and fault conditions. The charger continues to operate during cranking and running and accepts multiple AC voltage connections. OVERALL SIZE 80 mm x 205 mm x 135 mm (3.1″ x 8.1″ x 5.3″) WEIGHT 0.88 kg PRODUCT VARIANTS 9473-01 – 9473 24 volt 15 amp Intelligent Battery Charger (90-305v 50/60Hz)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT

DC OUTPUT 15 A DC 24 V DC RIPPLE AND NOISE 1% EFFICIENCY >90%

REGULATION

LINE <0.5% LOAD 2%

TEMPERATURE SENSOR INPUT

PT1000

PROTECTIONS

Short Circuit DC Over Voltage DC Over Current Reverse Polarity Over Temperature AC Under & Over Voltage

CHARGE FAILURE RELAY

3 A 30 V DC volt free relay  

The DSE9474 is an intelligent 24-volt, 30 amp CAN enabled switch-mode battery charger that can be programmed for different charging curves. This helps to maximise battery life. The charger is programmed using the DSE Configuration Suite Software. The charger can be DIN rail or chassis mounted and has three built-in LEDs to indicate current charging status and fault conditions. The charger continues to operate during cranking and running and accepts multiple AC voltage connections. OVERALL SIZE 240 mm x 263 mm x 89 mm (9.4” x 10.4” x 3.5”) WEIGHT 2.5kg PRODUCT VARIANTS 9474-01 - 24 volt 30 amp Intelligent Battery Charger (90-305v 50/60Hz)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT

DSE9474 DC OUTPUT 30 A DC 24 V DC RIPPLE AND NOISE 1% EFFICIENCY >90%

REGULATION

LINE <0.5% LOAD 1%

TEMPERATURE SENSOR INPUT

PT1000

PROTECTIONS

Short Circuit DC Under & Over Voltage DC Over Current Reverse Polarity Over Temperature AC Under & Over Voltage

CHARGE FAILURE RELAY

3 A 30 V DC volt free relay  

The DSE9476 is an intelligent 24-volt, 20 amp switch-mode battery charger that can be programmed for different charging curves. This helps to maximise battery life. OVERALL SIZE 183 mm x 233 mm x 76 mm (7.2” x 9.2” x 3.0”) WEIGHT 1.8kg PRODUCT VARIANTS 9476-01 - 24 V 20 A Intelligent Battery Charger

AC SUPPLY

VOLTAGE RANGE 95 V to 305 V (L-N) FREQUENCY RANGE 47 Hz to 63 Hz (L-N)

DC OUTPUT

DSE9476 OUTPUT 20 A DC at 24 V DC RIPPLE AND NOISE <1% EFFICIENCY >92%

REGULATION

LINE <0.5% LOAD 1%

TEMPERATURE SENSOR INPUT

PT1000

PROTECTIONS

Short Circuit DC Under & Over Voltage DC Over Current Reverse Polarity Over Temperature AC Under & Over Voltage

CHARGE FAILURE RELAY

3 A at 30 V DC volt free relay

OPERATING TEMPERATURE RANGE

-30 ˚C to +80 ˚C -22 ˚F to +176 ˚F

STORAGE TEMPERATURE RANGE

-40 ˚C to +85 ˚C -40 ˚F to +185 ˚F  

**Please Note: The DSE9701 has been discontinued. If ordered, you may receive the DSE9701 until stock is depleted or the DSE BC2405 will be the direct replacement** The DSE9701 24 volt 5 amp switch-mode battery charger keeps batteries charged to their maximum capacity at all times. It is designed for permanent battery connection and can be DIN rail or chassis mounted. The charger includes a normal or overload condition LED indicator on the front to assist with status identification. The charger operates during cranking and running and accepts multiple AC voltage connections. The charger incorporates premium grade capacitors and components to ensure premium levels of efficiency. The robustness of the design makes the charger perfect for heavy and light industrial environments. DIN RAIL MOUNTED 48 mm x 133 mm x 110 mm (1.9” x 5.2” x 4.3”) CHASSIS MOUNTED 48 mm x 153 mm x 112 mm (1.9” x 6.0” x 4.4”) WEIGHT 0.4kg PRODUCT VARIANTS 9701-01 – Vertical 24 Volt 5 Amp Battery Charger (90-305v 50/60Hz)

AC SUPPLY

FREQUENCY RANGE 45 Hz to 65 Hz VOLTAGE RANGE 90 V to 305 V (L-N)

DC OUTPUT

5 A DC 24 V DC RIPPLE AND NOISE <1% EFFICIENCY >80%

REGULATION

LINE <0.001% Vo LOAD 1% Vo

PROTECTIONS

Short Circuit Over Voltage Over Current Reverse Polarity  

**Please Note: The DSE9702 has been discontinued. If ordered, you may receive the DSE9702 until stock is depleted or the DSE BC1205 will be the direct replacement** The DSE9702 12 volt 5 amp switch-mode battery charger keeps batteries charged to their maximum capacity at all times. It is designed for permanent battery connection and can be DIN rail or chassis mounted. The charger includes a normal or overload condition LED indicator on the front to assist with status identification. The charger operates during cranking and running and accepts multiple AC voltage connections. The charger incorporates premium grade capacitors and components to ensure premium levels of efficiency. The robustness of the design makes the charger perfect for heavy and light industrial environments. DIN RAIL MOUNTED 48 mm x 133 mm x 110 mm (1.9” x 5.2” x 4.3”) SCREW MOUNTED 48 mm x 153 mm x 112 mm (1.9” x 6.0” x 4.4”) WEIGHT 0.4kg PRODUCT VARIANTS 9702-01 – Vertical 12 Volt 5 Amp Battery Charger (90-305v 50/60Hz)

AC SUPPLY

FREQUENCY RANGE 45 Hz to 65 Hz VOLTAGE RANGE 90 V to 305 V (L-N)

DC OUTPUT

5 A DC 12 V DC RIPPLE AND NOISE <1% EFFICIENCY >80%

REGULATION

LINE <0.001% Vo LOAD 1% Vo

PROTECTIONS

Short Circuit Over Voltage Over Current Reverse Polarity  

The DSEA106 MKII Digital Automatic Voltage Regulator (AVR) builds on the success of the DSEA106 product providing additional features to enhance customer applications. The product regulates the output voltage of an AC alternator and is supplied by a stator auxiliary winding or a shunt system taking power from the output windings. The product provides higher levels of stability compared to analogue designs by maintaining a smooth, stable and regulated AC output voltage that is unaffected by the connected electrical load. Please Note: The DSE815 interface is required for programming.

POWER SUPPLY

VOLTAGE RANGE 100 V AC to 300 V AC (Ph to N/Ph) FREQUENCY RANGE 40 Hz to 180 Hz

ALTERNATOR OUTPUT SENSING

VOLTAGE RANGE 15 V AC to 600 V AC (Ph to N/Ph) FREQUENCY RANGE 40 Hz to 65 Hz

EXCITATION OUTPUT

EXCITATOR FIELD WINDING IMPEDANCE 5 Ω to 50 Ω CONTINUOUS VOLTAGE RATING 0 V DC to 100 V DC CONTINUOUS CURRENT RATING 0 A DC to 7 A DC MAXIMUM CURRENT RATING 15 A DC for 10 seconds

QUADRATURE DROOP CT

MAXIMUM SECONDARY CURRENT 5 A AC BURDEN 0.25 VA ACCURACY 1%

REMOTE VOLTAGE ADJUSTMENT

POTENTIOMETER 5 kΩ VOLTAGE INPUT -10 V DC to 10 V DC OVERALL SIZE 179 mm x 108 mm x 61 mm (7.1” x 4.3” x 2.4”) PRODUCT VARIANTS A106-02 – A106 Digital AVR (AUX)  

The DSEA108 Digital Automatic Voltage Regulator (AVR) with CAN is designed to regulate the output voltage of an AC alternator. The DSEA108 is supplied by either a stator auxiliary winding or a shunt system taking power from the output windings. The DSEA108 eliminates the complexities involved with analogue AVR designs. Analogue AVR designs can be oversensitive to changes in temperature which affects stability whereas the DSEA108 AVR maintains a smooth, stable regulated AC output voltage regardless of the electrical load connected. POWER SUPPLY VOLTAGE RANGE 100 V AC to 300 V AC (Ph to N/Ph) FREQUENCY RANGE 40 Hz to 180 Hz ALTERNATOR OUTPUT SENSING VOLTAGE RANGE 15 V AC to 600 V AC (Ph to N/Ph) FREQUENCY RANGE 40 Hz to 65 Hz EXCITATION OUTPUT EXCITATOR FIELD WINDING IMPEDANCE 5 Ω to 50 Ω CONTINUOUS VOLTAGE RATING 0 V DC to 100 V DC CONTINUOUS CURRENT RATING 0 A DC to 7 A DC MAXIMUM CURRENT RATING 15 A DC for 10 seconds QUADRATURE DROOP CT MAXIMUM SECONDARY CURRENT 5 A AC BURDEN 0.25 VA ACCURACY 1% REMOTE VOLTAGE ADJUSTMENT POTENTIOMETER 5 kΩ VOLTAGE INPUT -10 V DC to 10 V DC DIMENSIONS 179 mm x 108 mm x 61 mm 7.1” x 4.3” x 2.4” STORAGE TEMPERATURE RANGE -40 °C to +85 °C -40 °F to +185 °F OPERATING TEMPERATURE RANGE -40 °C to +70 °C -40 °F to +158 °F WEIGHT 0.46 Kg.  

The DSEA109 Digital Automatic Voltage Regulator (AVR) with CAN is designed to regulate the output voltage of an AC alternator. The DSEA109 is supplied by either a 3 phase PMG, single phase PMG,  stator auxiliary winding or a shunt system taking power from the output windings. The DSEA109 eliminates the complexities involved with analogue AVR designs. Analogue AVR designs can be over sensitive to changes in temperature which affects stability whereas the DSEA109 AVR maintains a smooth, stable regulated AC output voltage, regardless of the electrical load connected.The DSEA109 also features 3-phase sensing for better regulation. Please Note: The DSE815 interface is required for programming. The DSEA109 is simple to install and set up using either the DSE Configuration Suite PC Software and the DSE815 configuration interface or five onboard potentiometers and 4 DIP switches, combined with a status LED providing a simple user interface. The DSEA109 Digital AVR has numerous advanced features such as a CAN port providing J1939 communications, soft start ramping, connection for a quadrature droop CT and the ability to perform remote voltage adjustment, making it perfect for synchronising and load sharing applications. The DSEA109 Digital AVR is an ideal option for both OEM and retro-fit solutions. OVERALL SIZE 180 mm x 145 mm x 61 mm (7.0” x 5.7” x 2.4”) WEIGHT 0.46 kg PRODUCT VARIANTS A109-01 – A109 Digital AVR With CAN Communications & PMG

POWER SUPPLY

VOLTAGE RANGE 100 V AC to 270 V AC (Ph to N & Ph to Ph) FREQUENCY RANGE 40 Hz to 400 Hz

ALTERNATOR OUTPUT SENSING

VOLTAGE RANGE 15 V AC to 600 V AC (Ph to Ph & Ph to N) FREQUENCY RANGE 40 Hz to 65 Hz

EXCITATION OUTPUT

EXCITER FIELD WINDING IMPEDANCE 5 Ω to 50 Ω CONTINUOUS VOLTAGE RATING 0 V DC to 100 V DC CONTINUOUS CURRENT RATING 0 A DC to 7 A DC MAXIMUM CURRENT RATING 15 A DC for 10 seconds

QUADRATURE DROOP CT

MAXIMUM SECONDARY CURRENT 5 A AC BURDEN 0.25 VA ACCURACY 1%

REMOTE VOLTAGE ADJUSTMENT

POTENTIOMETER 5 kΩ VOLTAGE INPUT -10 V DC to 10 V DC  

The eView® DSEE050 is a fully configurable colour engine display and controller designed to meet the demands of modern electronic engines and equipment applications. The DSEE050 supports J1939 electronics engines including Tier 4 final and stage V engine parameters and supports TSC 1 messaging allowing speed control messages to be sent over CAN. The engine display is an extremely powerful and versatile product suited to a wide number of different application environments. The DSEE050 is fully configurable using the licence-free DSE Configuration Suite software, which allows users to create custom configurations, event sequences and user interface screens. Users can also add company branding to the displays start-up screen and select from a light and dark background when the module is in use. OVERALL SIZE 112.5mm x 115 mm x 49 mm (4.43″ x 4.53″ x 1.93″) PANEL CUT OUT 80 mm / 3.15″ Diameter PRODUCT VARIANTS E050-01 – eView® Engine Display

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V TO 35 V continuous (5 V for up to 1 minute) CRANKING DROPOUTS Able to survive ) V for 100 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries MAXIMUM OPERATING CURRENT 300 mA at 12 V, 150 mA at 24 V MAXIMUM STANDBY CURRENT 80 mA at 12 V, 44 mA at 24 V

INPUTS

MULTI-FUNCTIONAL INPUTS A to D Configurable as: digital, current, voltage, resistance 0 V to 10 V 0 mA to 20 mA 0-3 kΩ

OUTPUTS

DC OUTPUTS A to C 1 A continuous at supply voltage VREF OUT 100 mA at 10 V / 5 V

OPERATING TEMPERATURE RANGE

-40 ° C to +85 ° C – 40 ° F to +185 ° F

HEATED DISPLAY OPERATING RANGE

Turns on at -25 ° C / -13 ° F Turns off at – 5 ° C / +23 ° F

STORAGE TEMPERATURE RANGE

-40 ° C to +85 ° C  

The E100 is an Engine Only Control Module designed to provide flexible engine control with built-in monitoring and protection. The module is fully configurable for a wide range of applications including engine driven pumps and compressors. Control functions include manual and automatic engine start and load control and built-in run-time scheduler. The DSEE100 also features an event log to help make fault diagnosis extremely simple. The module is configured using the DSE Configuration Suite software. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5″ x 4.4″ x 1.7″) PANEL CUT OUT 118 mm x 92 mm (4.6″ x 3.6″) PRODUCT VARIANTS E100-01 – E100 Engine Controller

DC SUPPLY

CONTINUOUS VOTLAGE RATING 8 V to 35 V continuous CRANKING DROPUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. MAXIMUM OPERATING CURRENT 85 mA at 12 V, 96 mA at 24 V MAXIMUM STANDBY CURRENT 51 mA at 12 V, 47 mA at 24 V MAXIMUM SLEEP CURRENT 35 mA at 12 V, 32 mA at 24 V CHARGE FAIL/EXCITATION RANGE 0 V to 35 V

INPUTS

DIGITAL INPUTS A to D Negative switching ANALOGUE INPUTS A to C Configurable as: Negative switching digital input Resistive

OUTPUTS

DC OUTPUT A (FUEL) & B (START) 10 A short-term 5 A continuous at supply voltage VOLT-FREE OUTPUTS C & D 2 A DC at supply voltage AUXILIARY OUTPUTS C, D, E & F 2 A DC at supply voltage PULSE PICK-UP VOLTAGE RANGE +/- 0.5 V to 70 V FREQUENCY RANGE 5 Hz to 10,000 Hz  

The DSEE400 is an IP67 rated engine control module that offers flexible control with built-in monitoring and protection. The control module is compatible with both electronic and mechanical diesel engines and be fully configured for a wide range of applications including engine driven pumps and compressors. All engine control functions including engine start, speed and clutch control can be achieved automatically and manually. NOW INCLUDES ADVANCED PLC EDITOR FUNCTIONALITY OVERALL SIZE 189 mm x 125 mm x 54 mm (7.5″ x 4.9″ x 2.1″) PANEL CUT OUT 148 mm x 112 mm (5.8″ x 4.4″) PRODUCT VARIANTS E400-01 – E400 Engine Controller E400-02 – E400 Engine Controller (Htr) RELATED PARTS 007-850 – Deutsch connector A (DT16-18SA-k004), 18 way complete with pins. 007-851 – Deutsch connector C (DT16-18SC-K004), 18 way complete with pins. 007-852 – Set of 2 harnesses, a & C connectors, pre-wired, 1.2 m cables marked.

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V continuous CRANKING DROPUTS Able to survive 0 V for 100 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. MAXIMUM OPERATING CURRENT 326 mA at 12 V, 164 mA at 24 V MAXIMUM STANDBY CURRENT 119 mA at 12 V, 60 mA at 24 V MAXIMUM OFF MODE CURRENT 76 mA at 12 V, 38 mA at 24 V CHARGE FAIL/EXCITATION RANGE 0 V to 35 V

INPUTS

DIGITAL INPUTS A to D Configurable as: Positive switching Negative switching ANALOGUE INPUTS A to G Configurable as: Negative switching digital input 0 V to 10 V 4 mA to 20 mA Resistive

OUTPUTS

DC OUTPUT A (FUEL) & B (START) 10 A for 10 seconds, 5 A continuous at supply voltage VOLT-FREE OUTPUTS C & D 2 A DC at supply voltage PWMI OUTPUTS E & F 4 A at supply voltage 20 Hz to 250 Hz

PULSE PICK-UP

VOLTAGE RANGE 0.5 V to 60 V RMS Fully isolated FREQUENCY RANGE 5 Hz to 10,000 Hz

GOVERNOR OUTPUT

Fully isolated VOLTAGE OUTPUT 0 V to 10 V range 1000 Ω minimum load impedance CURRENT OUTPUT 0 V to 20 mA range 500 Ω maximum load impedance  

The DSEE400 is an IP67 rated engine control module that offers flexible control with built-in monitoring and protection. The control module is compatible with both electronic and mechanical diesel engines and be fully configured for a wide range of applications including engine driven pumps and compressors. All engine control functions including engine start, speed and clutch control can be achieved automatically and manually. NOW INCLUDES ADVANCED PLC EDITOR FUNCTIONALITY OVERALL SIZE 189 mm x 125 mm x 54 mm (7.5″ x 4.9″ x 2.1″) PANEL CUT OUT 148 mm x 112 mm (5.8″ x 4.4″) PRODUCT VARIANTS E400-01 – E400 Engine Controller E400-02 – E400 Engine Controller (Htr) RELATED PARTS 007-850 – Deutsch connector A (DT16-18SA-k004), 18 way complete with pins. 007-851 – Deutsch connector C (DT16-18SC-K004), 18 way complete with pins. 007-852 – Set of 2 harnesses, a & C connectors, pre-wired, 1.2 m cables marked.

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V continuous CRANKING DROPUTS Able to survive 0 V for 100 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. MAXIMUM OPERATING CURRENT 326 mA at 12 V, 164 mA at 24 V MAXIMUM STANDBY CURRENT 119 mA at 12 V, 60 mA at 24 V MAXIMUM OFF MODE CURRENT 76 mA at 12 V, 38 mA at 24 V CHARGE FAIL/EXCITATION RANGE 0 V to 35 V

INPUTS

DIGITAL INPUTS A to D Configurable as: Positive switching Negative switching ANALOGUE INPUTS A to G Configurable as: Negative switching digital input 0 V to 10 V 4 mA to 20 mA Resistive

OUTPUTS

DC OUTPUT A (FUEL) & B (START) 10 A for 10 seconds, 5 A continuous at supply voltage VOLT-FREE OUTPUTS C & D 2 A DC at supply voltage PWMI OUTPUTS E & F 4 A at supply voltage 20 Hz to 250 Hz

PULSE PICK-UP

VOLTAGE RANGE 0.5 V to 60 V RMS Fully isolated FREQUENCY RANGE 5 Hz to 10,000 Hz

GOVERNOR OUTPUT

Fully isolated VOLTAGE OUTPUT 0 V to 10 V range 1000 Ω minimum load impedance CURRENT OUTPUT 0 V to 20 mA range 500 Ω maximum load impedance  

The DSEE800 engine control module has been designed to provide flexible control and monitoring for engine driven pumps, compressors, hydraulic power packs and off-highway machinery. The control module can be used with electronic and mechanical diesel engines and offers outstanding flexibility via its integrated PLC editor. This flexibility enables users to match required operating modes unique to their applications. A number of comprehensive communication and system expansion options allows users to extend the input/output capabilities of the system and communicate across complex networks. OVERALL SIZE 240 mm x 172 mm x 57 mm (9.4” x 6.8” x 2.2”) PANEL CUTOUT SIZE 220 mm x 160 mm (8.7 ” x 6.3″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.88kg PRODUCT VARIANTS E800-01 – E800 Engine Control Module

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V continuous CRANKING DROPUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. MAXIMUM OPERATING CURRENT 510 mA at 12 V, 238 mA at 24 V MAXIMUM STANDBY CURRENT 226 mA at 12 V, 107 mA at 24 V MAXIMUM OFF MODE CURRENT 180 mA at 12 V, 86 mA at 24 V CHARGE FAIL/EXCITATION RANGE 0 V to 35 V

INPUTS

DIGITAL INPUTS A to K Configurable as: Positive switching Negative switching RATIOMETRIC INPUTS B to L Configurable as: Negative switching digital input 0 V to 10 V 4 mA to 20 mA 0 Ω to 1920 Ω

OUTPUTS

DC OUTPUT A (FUEL) & B (START) 10 A for 10 seconds, 5 A continuous at supply voltage VOLT-FREE OUTPUTS C & D 5 A DC at 35 V DC 8 A AC at 250 V AC DC OUTPUTS E, F, G & H 2 A DC at supply voltage PWM OUTPUTS I, J, K & L 4 A at supply voltage 20 Hz to 250 Hz

PULSE PICK-UP

VOLTAGE RANGE ±0.5 V to 60 V RMS Fully isolated FREQUENCY RANGE 10,000 Hz (max)

BUILT-IN GOVERNOR CONTROL

MINIMUM LOAD IMPEDANCE 1000 Ω Fully isolated GAIN VOLTAGE 0 V to 10 V DC OFFSET VOLTAGE ±10 V DC  

The DSEG0123 Analogue Load Share Lines Interface converts DSE AMSC / MSC digital load share communications to universal analogue load share lines, allowing DSE paralleling controllers to seamlessly deliver kW and kvar load sharing with third party manufactured products. The DSEG0123 also allows the DSEG8600, DSEG8900, DSE8610 MKII, DSE8610, DSE7510 and DSE5510 controllers to be added to an existing DSE load sharing application and deliver kW and kvar load sharing across all DSE controllers within the system. The flexibility of the DSEG0123 makes expanding existing systems extremely simple. OVERALL SIZE 164.5 mm x 76.4 mm x 48.9 mm (6.48″ x 3.0″ x 1.93″) WEIGHT 0.2kg PRODUCT VARIANTS G0123-01 – Analogue Loadshare Lines Interface Key Features:

• Converts a DSE MSC link to analogue load share lines
• Compatible with multiple manufacturers paralleling controllers
• Configuration Suite PC software configuration
• PC SCADA instrumentation for system diagnostics
• Power on / status LEDs
• USB programming port

Key Benefits:

• Allows controllers to communicate with controllers of a different type or manufacturer
• Ultimate flexibility across a wide range of existing applications
• Intuitive user programming using the standard DSE software platform
• Provides detailed monitoring information
• Easily view what mode the product is in
• Provides simple universal connection

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V DC Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 150 mA at 12 V, 80 mA at 24 V MAXIMUM STANDBY CURRENT 150 mA at 12 V, 80 mA at 24 V  

The DSEL401 MKII is an intelligent control module designed specifically for mobile lighting tower applications. The control module provides class leading flexible features that are fully configurable to suit multiple complex lighting sequences. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.7”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6” x 3.6”) MAXIMUM PANEL THICKNESS 8.0mm (0.3”) WEIGHT 0.28kg PRODUCT VARIANTS L401-01 – L401 MKII Intelligent Lighting Tower Control Module (Rtc)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 85 mA at 12 V, 96 mA at 24 V MAXIMUM STANDBY CURRENT 51 mA at 12 V, 47 mA at 24 V MAXIMUM SLEEP CURRENT 35 mA at 12 V, 32 mA at 24 V MAXIMUM DEEP SLEEP CURRENT <10 uA at 12 V, <10 uA at 24 V

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTS C to J 2 A DC at supply voltage ­­

GENERATOR

VOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz  

The DSEL401 MKII is an intelligent control module designed specifically for mobile lighting tower applications. The control module provides class leading flexible features that are fully configurable to suit multiple complex lighting sequences. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.7”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6” x 3.6”) MAXIMUM PANEL THICKNESS 8.0mm (0.3”) WEIGHT 0.28kg PRODUCT VARIANTS L401-01 – L401 MKII Intelligent Lighting Tower Control Module (Rtc)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 85 mA at 12 V, 96 mA at 24 V MAXIMUM STANDBY CURRENT 51 mA at 12 V, 47 mA at 24 V MAXIMUM SLEEP CURRENT 35 mA at 12 V, 32 mA at 24 V MAXIMUM DEEP SLEEP CURRENT <10 uA at 12 V, <10 uA at 24 V

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTS C to J 2 A DC at supply voltage ­­

GENERATOR

VOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz  

The M040 is a development kit for the M64X controller range. It allows the user to connect the breakout PCB to a laptop and control unit to assist with application development. OVERALL SIZE Breakout PCB 46 mm x 320 mm x 210 mm (1.81” x 12.60” x 8.27”) Case 160 mm x 437 mm x 379 mm (6.3” x 17.20” x 14.92”) WEIGHT 4.25 kg PRODUCT VARIANTS M040-01 – M040 Development Kit M040 DEVELOPMENT KIT DOES NOT INCLUDE A DSEM640 OR LAPTOP.

DC SUPPLY

6 V DC to 32 V DC (for M640)

TOTAL INPUTS/OUTPUTS

68 (32 inputs/36 outputs) (for M640) INPUTS 32 Sprung Terminal Blocks (Split into 2 Blocks) OUTPUTS 36 Sprung Terminal Blocks (Split into 2 Blocks)

INTERFACES

CAN 1 to 4 SubD9 Female Connectors and Sprung Terminal Blocks. Built-in 120 Ω Termination Resistors via Jumper Connectors.

DIMENSIONS

-40 ˚ C to +85 ˚ C -40 ˚ F to +185 ˚ F

The DSEM240 is a CAN Slave Unit designed for use on vehicles and off-highway machinery. Developed to provide additional I/O for expanding networks, the DSEM240 works with any J1939/CAN open network. The M240 can be used with both DSE and 3rd party equipment and can be configured using any CAN tool. OVERALL SIZE 49 mm x 240 mm x 190 mm (H x W x D) 1.46″ x 9.45″ x 7.48″ (H x W x D) WEIGHT <1.5 kg PRODUCT VARIANTS M240-01 – M240 CAN Slave Unit (J1939) M240-02 – M240 CAN Slave Unit (CAN Open)

DC SUPPLY

8 V DC to 32 V DC

CURRENT CONSUMPTION

OPERATING CURRENT <300 mA at 24 V without external loads

TOTAL INPUTS/OUTPUTS 

44 (20 inputs / 24 outputs) INPUTS Configurable Digital inputs (active high/active low) Analogue inputs voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V current 4 mA to 20 mA, Ratiometric, Resistive, Frequency, Pulse Count OUTPUTS Configurable 2 A / 4 A Digital Output High-Sided, Low-Sided PWM, PWMi

INTERFACES

CAN 1 J1939 or CAN Open

DIMENSIONS

37 mm x 240 mm x 190 mm (H x W x D) 1.46 ” x 9.45 ” x 7.48 ” (H x W x D)

WEIGHT

<1.5 kg

STORAGE TEMPERATURE RANGE

-40 ˚C to +85 ˚C -40 ˚F to +185 ˚F

OPERATING TEMPERATURE RANGE

-40 ˚C to +85 ˚C -40 ˚F to +185 ˚F (at full load)

PROTECTION RATING

IP67 (with mating connectors)

MOUNTING

4 x M6 bolts  

The DSEM240 is a CAN Slave Unit designed for use on vehicles and off-highway machinery. Developed to provide additional I/O for expanding networks, the DSEM240 works with any J1939/CAN open network. The M240 can be used with both DSE and 3rd party equipment and can be configured using any CAN tool. OVERALL SIZE 49 mm x 240 mm x 190 mm (H x W x D) 1.46″ x 9.45″ x 7.48″ (H x W x D) WEIGHT <1.5 kg PRODUCT VARIANTS M240-01 – M240 CAN Slave Unit (J1939) M240-02 – M240 CAN Slave Unit (CAN Open)

DC SUPPLY

8 V DC to 32 V DC

CURRENT CONSUMPTION

OPERATING CURRENT <300 mA at 24 V without external loads

TOTAL INPUTS/OUTPUTS 

44 (20 inputs / 24 outputs) INPUTS Configurable Digital inputs (active high/active low) Analogue inputs voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V current 4 mA to 20 mA, Ratiometric, Resistive, Frequency, Pulse Count OUTPUTS Configurable 2 A / 4 A Digital Output High-Sided, Low-Sided PWM, PWMi

INTERFACES

CAN 1 J1939 or CAN Open

DIMENSIONS

37 mm x 240 mm x 190 mm (H x W x D) 1.46 ” x 9.45 ” x 7.48 ” (H x W x D)

WEIGHT

<1.5 kg

STORAGE TEMPERATURE RANGE

-40 ˚C to +85 ˚C -40 ˚F to +185 ˚F

OPERATING TEMPERATURE RANGE

-40 ˚C to +85 ˚C -40 ˚F to +185 ˚F (at full load)

PROTECTION RATING

IP67 (with mating connectors)

MOUNTING

4 x M6 bolts  

The DSE M640 provides advanced programmable control options for vehicles and off-highway machinery and has been developed specifically for mobile applications. Sealed to IP67, the device incorporates a breather to allow the unit to equalise pressure and reduce condensation whilst filtering out liquids and other contaminants. The unit features Ethernet, USB, CAN and configurable I/O. Inside the unit is a powerful 32 bit processor with a 220 MHz clock speed for outstanding operating response times. There are also 4 independent CAN interfaces, J1939, CAN Open and Raw CAN. Flexible user programming is provided via CODESYS 3.5 (C programming on request). OVERALL SIZE 49 mm x 240 mm x 190 mm (H x W x D) 1.46″ x 9.45″ x 7.48″ (H x W x D) WEIGHT 1.5 kg

DC SUPPLY

8 V DC to 36 V DC

CURRENT CONSUMPTION

OPERATING CURRENT <300 mA at 24 V without external loads

TOTAL INPUTS/OUTPUTS

68 (32 inputs / 36 outputs) INPUTS Configurable Data inputs (positive/negative) Analogue inputs voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V current 4mA to 20mA, Ratiometric, Resistive, Frequency, Phase, Fast Counter, Encoder OUTPUTS Configurable 2 A / 4 A Digital Output high-sided, low-sided PWM, PWMi

INTERFACES

CAN1..4 Can interfaces 2.0 A/B, ISO 11898 50kbit/s…1Mbit/s J1939, CAN Open and Raw CAN ETHERNET 10 Mbit/s / 100 Mbit/s, Duplex USB USB Host 2.0 (12Mbit/s)

STORAGE TEMPERATURE RANGE

-40 ˚C to +85 ˚C -40 ˚F to +185 ˚F

OPERATING TEMPERATURE RANGE

-40 ˚C to +85 ˚C -40 ˚F to +185 ˚F (at full load)

PROTECTION RATING

IP67 (with mating connectors)

MOUNTING

4 x M6 bolts  

The DSE M643 provides advanced programmable control options for vehicles and off-highway machinery and has been developed specifically for mobile applications. Sealed to IP67, the device incorporates a breather to allow the unit to equalise pressure and reduce condensation whilst filtering out liquids and other contaminants. The unit features Ethernet, USB, CAN and  configurable I/O. Inside the unit is a powerful 32 bit processor with a 220 MHz clock speed for outstanding operating response times. There are also 4 independent CAN interfaces, J1939, CAN Open and Raw CAN. Flexible user programming is provided via CODESYS 3.5 (C programming on request). OVERALL SIZE 49 mm x 240 mm x 190 mm (H x W x D) 1.46″ x 9.45″ x 7.48″ (H x W x D) WEIGHT 1.5 kg

DC SUPPLY

8 V DC to 36 V DC

CURRENT CONSUMPTION

OPERATING CURRENT <300 mA at 24 V without external loads

TOTAL INPUTS/OUTPUTS

34 (16 inputs /18 outputs) INPUTS Configurable Data inputs (positive/negative) Analogue inputs voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V current 4mA to 20mA, Ratiometric, Resistive, Frequency, Phase, Fast Counter, Encoder OUTPUTS Configurable 2 A / 4 A Digital Output high-sided, low-sided PWM, PWMi

INTERFACES

CAN1..4 Can interfaces 2.0 A/B, ISO 11898 50kbit/s…1Mbit/s J1939, CAN Open and Raw CAN ETHERNET 10 Mbit/s / 100 Mbit/s, Duplex USB USB Host 2.0 (12Mbit/s)

STORAGE TEMPERATURE RANGE

-40 ˚C to +85 ˚C -40 ˚F to +185 ˚F

OPERATING TEMPERATURE RANGE

-40 ˚C to +85 ˚C -40 ˚F to +185 ˚F (at full load)

PROTECTION RATING

IP67 (with mating connectors)

MOUNTING

4 x M6 bolts  

The DSEM812 is a 12″ Programmable Display designed for use on vehicles and off highway machinery and is the largest display in DSE’s programmable display range. Developed for use as a standalone product or with the DSEM64x programmable controllers, the DSEM812 provides users with outstanding flexibility. The M812 is configured using CODESYS 3.5 or Qt, can be RAM or panel mounted and has the option to use in portrait or landscape orientation. OVERALL SIZE 330 mm x 210 mm x 63.5 mm (12.99” x 8.26” x 2.5”) WEIGHT 2.12 kg PRODUCT VARIANTS M812-01 – CODESYS  (Keyed) M812-03 – Qt (Keyed)

DC SUPPLY

8 V DC to 32 V DC

CURRENT CONSUMPTION

OPERATING CURRENT < 1000 mA at 12 V and 24 V without external loads

DISPLAY

12.1″ TFT, 1280 x 800 16:10 resolution 24 bit colour Optically bonded

INPUTS/OUTPUTS (Total)

6 inputs / 6 outputs INPUTS Configurable, Digital inputs (positive / negative) Analogue inputs (Voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V, current 4 mA to 20 mA, Ratiometric, Resistive, Frequency) OUTPUTS Configurable Digital Output High-Sided/Low-Sided PWM INTERFACES CAN 1-3 CAN Interfaces 2.0 A/B, ISO11898 50 kbits/s… 1 Mbit/s CAN Open, SAE J1939 or Raw CAN ETHERNET 1-2 10 Mbit/s / 100 Mbit/s, Duplex USB USB Host 2.0 (12 Mbit/s)

DIMENSIONS

Keyed 330 mm x 210 mm x 63.5 mm (W x H x D) 12.99” x 8.26” x 2.5” ( W x H x D) Non Keyed 330 mm x 210 mm x 59.7 mm (W x H x D) 12.99” x 8.26” x 2.35” ( W x H x D)

WEIGHT

2.12 kg

STORAGE TEMPERATURE RANGE

-30 ˚ C to +80 ˚ C -22 ˚ F to +176 ˚ F

OPERATING TEMPERATURE RANGE

-20 ˚ C to +70 ˚ C -4 ˚ F to +158 ˚ F

PROTECTION RATING

IP67/NEMA 6 (with mating connectors)

MOUNTING

RAM / Panel Mount  

The DSEM812 is a 12″ Programmable Display designed for use on vehicles and off highway machinery and is the largest display in DSE’s programmable display range. Developed for use as a standalone product or with the DSEM64x programmable controllers, the DSEM812 provides users with outstanding flexibility. The M812 is configured using CODESYS 3.5 or Qt, can be RAM or panel mounted and has the option to use in portrait or landscape orientation. OVERALL SIZE 330 mm x 210 mm x 63.5 mm (12.99” x 8.26” x 2.5”) WEIGHT 2.12 kg PRODUCT VARIANTS M812-01 – CODESYS  (Keyed) M812-03 – Qt (Keyed)

DC SUPPLY

8 V DC to 32 V DC

CURRENT CONSUMPTION

OPERATING CURRENT < 1000 mA at 12 V and 24 V without external loads

DISPLAY

12.1″ TFT, 1280 x 800 16:10 resolution 24 bit colour Optically bonded

INPUTS/OUTPUTS (Total)

6 inputs / 6 outputs INPUTS Configurable, Digital inputs (positive / negative) Analogue inputs (Voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V, current 4 mA to 20 mA, Ratiometric, Resistive, Frequency) OUTPUTS Configurable Digital Output High-Sided/Low-Sided PWM INTERFACES CAN 1-3 CAN Interfaces 2.0 A/B, ISO11898 50 kbits/s… 1 Mbit/s CAN Open, SAE J1939 or Raw CAN ETHERNET 1-2 10 Mbit/s / 100 Mbit/s, Duplex USB USB Host 2.0 (12 Mbit/s)

DIMENSIONS

Keyed 330 mm x 210 mm x 63.5 mm (W x H x D) 12.99” x 8.26” x 2.5” ( W x H x D) Non Keyed 330 mm x 210 mm x 59.7 mm (W x H x D) 12.99” x 8.26” x 2.35” ( W x H x D)

WEIGHT

2.12 kg

STORAGE TEMPERATURE RANGE

-30 ˚ C to +80 ˚ C -22 ˚ F to +176 ˚ F

OPERATING TEMPERATURE RANGE

-20 ˚ C to +70 ˚ C -4 ˚ F to +158 ˚ F

PROTECTION RATING

IP67/NEMA 6 (with mating connectors)

MOUNTING

RAM / Panel Mount  

Panel mount kit for use with the M812 (keyed).

KEY FEATURES

• Allows the M812 to be mounted within a panel

KEY BENEFITS

• Enables the M812 to be securely held in place within a dashboard

 

The DSEM812 is a 12″ Programmable Display designed for use on vehicles and off highway machinery and is the largest display in DSE’s programmable display range. Developed for use as a standalone product or with the DSEM64x programmable controllers, the DSEM812 provides users with outstanding flexibility. The DSEM812 is configured using CODESYS 3.5 or Qt, can be RAM or panel mounted and has the option to use in portrait or landscape orientation. OVERALL SIZE 330 mm x 210 mm x 59.7 mm (12.99” x 8.26” x 2.35”) WEIGHT 2.12 kg PRODUCT VARIANTS M812-02 – CODESYS  (Non Keyed) M812-04 – Qt (Non Keyed)

DC SUPPLY

8 V DC to 32 V DC

CURRENT CONSUMPTION

OPERATING CURRENT < 1000 mA at 12 V and 24 V without external loads

DISPLAY

12.1″ TFT, 1280 x 800 16:10 resolution 24 bit colour Optically bonded

The DSEM812 is a 12″ Programmable Display designed for use on vehicles and off highway machinery and is the largest display in DSE’s programmable display range. Developed for use as a standalone product or with the DSEM64x programmable controllers, the DSEM812 provides users with outstanding flexibility. The DSEM812 is configured using CODESYS 3.5 or Qt, can be RAM or panel mounted and has the option to use in portrait or landscape orientation. OVERALL SIZE 330 mm x 210 mm x 59.7 mm (12.99” x 8.26” x 2.35”) WEIGHT 2.12 kg PRODUCT VARIANTS M812-02 – CODESYS  (Non Keyed) M812-04 – Qt (Non Keyed)

DC SUPPLY

8 V DC to 32 V DC

CURRENT CONSUMPTION

OPERATING CURRENT < 1000 mA at 12 V and 24 V without external loads

DISPLAY

12.1″ TFT, 1280 x 800 16:10 resolution 24 bit colour Optically bonded

Panel mount kit for use with the M812. Non Keyed.

KEY FEATURES

• Allows the M812 to be mounted within a panel

KEY BENEFITS

• Enables the M812 to be securely held in place within a dashboard

 

GPS Antenna (SMA) M with 3 metre cable.  

Set of 2 coded AMP SEAL connectors pre-wired with 1.2 m (3ft 11") cable.

KEY FEATURES

• Set of 2 coded AMP SEAL connectors pre-wired with 1.2 m (3ft 11") cable

KEY BENEFITS

• Premium Quality IP65 rated connectors provide outstanding reliability

 

Set of 2 coded AMP SEAL connectors complete with crimps/contacts.

KEY FEATURES

• Set of 2 coded AMP SEAL connectors complete with crimps/contacts.

KEY BENEFITS

• Premium Quality IP65 rated connectors provide outstanding reliability.

 

The DSEM835 is a 3.5″ programmable display designed for use on vehicles and off highway machinery. The DSEM835 provides users with outstanding flexibility. The DSEM835 is configured using CODESYS 3.5. Key Features of the product include: Multi-Functional Inputs, Flexible Outputs, Heated Optically Bonded Display and Tier 4F Stage 5 Engine Support. OVERALL SIZE 112.5 mm x 115 mm x 49 mm (4.438” x 4.53” x 1.93”) WEIGHT < 1 kg CUT-OUT 80 mm diameter (3.15″) PRODUCT VARIANTS M835-01 – M835 Programmable Display

DC SUPPLY

8 V DC to 32 V DC

CURRENT CONSUMPTION

OPERATING CURRENT < 1000 mA at 12 V and 24 V without external loads

DISPLAY

320 px x 240 px 24 bit colour Optically bonded

INPUTS/OUTPUTS (total)

4 inputs / 3 outputs INPUTS Configurable as: digital, current, voltage, resistance 0 V to 10 V, 0 mA to 10 mA, 0 – 3 kΩ OUTPUTS 1 A continuous at supply voltage VREF OUT 100 mA at 10 V / 5 V

INTERFACES

CAN 1 CAN Interfaces 2.0 A/B, ISO11898 50 kbits/s… 1 Mbit/s SAE J1939 or Raw CAN Configurable internal software 120 Ω resistor

DIMENSIONS

112.5 mm x 115 mm x 49 mm (W x H x D) 4.43” x 4.53” x 1.93” ( W x H x D)

WEIGHT

< 1 kg

STORAGE TEMPERATURE RANGE

-40 ˚ C to +85 ˚ C -40 ˚ F to +185 ˚ F

OPERATING TEMPERATURE RANGE

-40 ˚ C to +85 ˚ C -22 ˚ F to +185 ˚ F

PROTECTION RATING

IP67/NEMA 6 (with mating connectors)

MOUNTING

Panel Mount (80 mm / 3.15″ diameter)  

The DSEM840 is a 4.3″ programmable display developed for use on vehicles and off-highway machinery. The display provides high levels of flexibility for multiple application types and is configured using CODESYS 3.5. The M840 can be used as a stand alone product or with additional M-Series products to create extremely powerful applications. OVERALL SIZE 131 mm x 208 mm x 56 mm (5.15” x 8.2” x 2.2”) WEIGHT < 1 kg CUT-OUT 163 mm x 98 mm (6.42″ x 3.86″) PRODUCT VARIANTS M840-01 – M840 Programmable Display

DC SUPPLY

8 V DC to 32 V DC

CURRENT CONSUMPTION

OPERATING CURRENT < 1000 mA at 12 V and 24 V without external loads DISPLAY 480 px x 272 px 24 bit colour Optically bonded

INPUTS/OUTPUTS (total)

4 inputs / 4 outputs INPUTS Configurable, Digital inputs (positive / negative) Analogue inputs (Voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V, current 4 mA to 20 mA, Ratiometric, Resistive, Frequency) OUTPUTS Configurable Digital Output High-Sided/Low-Sided VREF OUT 150 mA at 10 V / 5 V

INTERFACES

CAN 1.2 CAN Interfaces 2.0 A/B, ISO11898 50 kbits/s… 1 Mbit/s CAN Open, SAE J1939 or Raw CAN ETHERNET 10 Mbit/s / 100 Mbit/s, Duplex USB USB Host 2.0 (12 Mbit/s)

DIMENSIONS

131 mm x 208 mm x 56 mm (W x H x D) 5.15” x 8.2” x 2.2” ( W x H x D)

WEIGHT

< 1 kg

STORAGE TEMPERATURE RANGE

-40 ˚ C to +80 ˚ C -40 ˚ F to +176 ˚ F

OPERATING TEMPERATURE RANGE

-30 ˚ C to +65 ˚ C -22 ˚ F to +149 ˚ F

PROTECTION RATING

IP67/NEMA 6 (with mating connectors)

MOUNTING

4 x M5 bolts / RAM arm  

The DSEM870 is a 7″ programmable display designed for use on vehicles and off highway machinery. Developed for use as a standalone product or with the DSEM640 programmable controller, the DSEM870 provides users with outstanding flexibility. The M870 is configured using CODESYS 3.5 (M870-01 / M870-02 / M870-03) or Qt (M870-04). M870-04 Qt (Touchscreen) Variant – Now Available. Option to Mount in Landscape/Portrait Mode. OVERALL SIZE 272 mm x 165 mm x 81 mm (10.8” x 6.3” x 3.15”) WEIGHT 1.25kg CUT-OUT 231 mm x 133 mm (9.09″ x 5.24″) PRODUCT VARIANTS M870-01 – CODESYS (Standard) M870-02 – CODESYS (Touchscreen) M870-03 – CODESYS (Standard with WebVisu) M870-04 – Qt (Touchscreen)

DC SUPPLY

8 V DC to 36 V DC

CURRENT CONSUMPTION

OPERATING CURRENT < 1000 mA at 12 V and 24 V without external loads < 1500 mA at 12 V and 24 V with Htr.

DISPLAY

800 px x 480 px 24 bit colour Optically bonded

INPUTS/OUTPUTS (total)

4 inputs / 4 outputs INPUTS Configurable, Digital inputs (positive / negative) Analogue inputs (Voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V, current 4 mA to 20 mA, Ratiometric, Resistive, Frequency) OUTPUTS Configurable Digital Output High-Sided/Low-Sided VREF OUT 500 mA at 10 V / 5 V

INTERFACES

CAN 1.2 CAN Interfaces 2.0 A/B, ISO11898 50 kbits/s… 1 Mbit/s CAN Open, SAE J1939 or Raw CAN ETHERNET 10 Mbit/s / 100 Mbit/s, Duplex USB USB Host 2.0 (480 Mbit/s)

DIMENSIONS

272 mm x 165 mm x 81 mm (W x H x D) 10.8” x 6.3” x 3.15” ( W x H x D)

WEIGHT

1.25 kg

STORAGE TEMPERATURE RANGE

-40 ˚ C to +85 ˚ C -40 ˚ F to +185 ˚ F

OPERATING TEMPERATURE RANGE

-30 ˚ C to +85 ˚ C -22 ˚ F to +185 ˚ F

PROTECTION RATING

IP67/NEMA 6 (with mating connectors)

MOUNTING

8 x M5 bolts / RAM arm  

The DSEM870 is a 7″ programmable display designed for use on vehicles and off highway machinery. Developed for use as a standalone product or with the DSEM640 programmable controller, the DSEM870 provides users with outstanding flexibility. The M870 is configured using CODESYS 3.5 (M870-01 / M870-02 / M870-03) or Qt (M870-04). M870-04 Qt (Touchscreen) Variant – Now Available. Option to Mount in Landscape/Portrait Mode. OVERALL SIZE 272 mm x 165 mm x 81 mm (10.8” x 6.3” x 3.15”) WEIGHT 1.25kg CUT-OUT 231 mm x 133 mm (9.09″ x 5.24″) PRODUCT VARIANTS M870-01 – CODESYS (Standard) M870-02 – CODESYS (Touchscreen) M870-03 – CODESYS (Standard with WebVisu) M870-04 – Qt (Touchscreen)

DC SUPPLY

8 V DC to 36 V DC

CURRENT CONSUMPTION

OPERATING CURRENT < 1000 mA at 12 V and 24 V without external loads < 1500 mA at 12 V and 24 V with Htr.

DISPLAY

800 px x 480 px 24 bit colour Optically bonded

INPUTS/OUTPUTS (total)

4 inputs / 4 outputs INPUTS Configurable, Digital inputs (positive / negative) Analogue inputs (Voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V, current 4 mA to 20 mA, Ratiometric, Resistive, Frequency) OUTPUTS Configurable Digital Output High-Sided/Low-Sided VREF OUT 500 mA at 10 V / 5 V

INTERFACES

CAN 1.2 CAN Interfaces 2.0 A/B, ISO11898 50 kbits/s… 1 Mbit/s CAN Open, SAE J1939 or Raw CAN ETHERNET 10 Mbit/s / 100 Mbit/s, Duplex USB USB Host 2.0 (480 Mbit/s)

DIMENSIONS

272 mm x 165 mm x 81 mm (W x H x D) 10.8” x 6.3” x 3.15” ( W x H x D)

WEIGHT

1.25 kg

STORAGE TEMPERATURE RANGE

-40 ˚ C to +85 ˚ C -40 ˚ F to +185 ˚ F

OPERATING TEMPERATURE RANGE

-30 ˚ C to +85 ˚ C -22 ˚ F to +185 ˚ F

PROTECTION RATING

IP67/NEMA 6 (with mating connectors)

MOUNTING

8 x M5 bolts / RAM arm  

The DSEM870 is a 7″ programmable display designed for use on vehicles and off highway machinery. Developed for use as a standalone product or with the DSEM640 programmable controller, the DSEM870 provides users with outstanding flexibility. The M870 is configured using CODESYS 3.5 (M870-01 / M870-02 / M870-03) or Qt (M870-04). M870-04 Qt (Touchscreen) Variant – Now Available. Option to Mount in Landscape/Portrait Mode. OVERALL SIZE 272 mm x 165 mm x 81 mm (10.8” x 6.3” x 3.15”) WEIGHT 1.25kg CUT-OUT 231 mm x 133 mm (9.09″ x 5.24″) PRODUCT VARIANTS M870-01 – CODESYS (Standard) M870-02 – CODESYS (Touchscreen) M870-03 – CODESYS (Standard with WebVisu) M870-04 – Qt (Touchscreen)

DC SUPPLY

8 V DC to 36 V DC

CURRENT CONSUMPTION

OPERATING CURRENT < 1000 mA at 12 V and 24 V without external loads < 1500 mA at 12 V and 24 V with Htr.

DISPLAY

800 px x 480 px 24 bit colour Optically bonded

INPUTS/OUTPUTS (total)

4 inputs / 4 outputs INPUTS Configurable, Digital inputs (positive / negative) Analogue inputs (Voltage 0 V to 5 V, 0 V to 10 V, 0 V to 32 V, current 4 mA to 20 mA, Ratiometric, Resistive, Frequency) OUTPUTS Configurable Digital Output High-Sided/Low-Sided VREF OUT 500 mA at 10 V / 5 V

INTERFACES

CAN 1.2 CAN Interfaces 2.0 A/B, ISO11898 50 kbits/s… 1 Mbit/s CAN Open, SAE J1939 or Raw CAN ETHERNET 10 Mbit/s / 100 Mbit/s, Duplex USB USB Host 2.0 (480 Mbit/s)

DIMENSIONS

272 mm x 165 mm x 81 mm (W x H x D) 10.8” x 6.3” x 3.15” ( W x H x D)

WEIGHT

1.25 kg

STORAGE TEMPERATURE RANGE

-40 ˚ C to +85 ˚ C -40 ˚ F to +185 ˚ F

OPERATING TEMPERATURE RANGE

-30 ˚ C to +85 ˚ C -22 ˚ F to +185 ˚ F

PROTECTION RATING

IP67/NEMA 6 (with mating connectors)

MOUNTING

8 x M5 bolts / RAM arm