Rear mount panel bracket for use with the DSE86xx MKII units. The bracket fixes into the rear of a panel and a control module is clipped in screen side down, leaving the rear of the module exposed for easy wiring connection.

KEY FEATURES

• Designed from durable black plastic
• Simple push and click module location points
• Enables a standard DSE86xx MKII control module to be used as a rear mount solution with a DSE8003 MKII display

KEY BENEFITS

• Turns standard DSE8610/DSE8610 MKII control modules into rear mount solutions
• Robust material suitable for rear panel mounting
• Control module can easily be mounted without any tools

 

Dual GPS GSM Antenna for use with the DSE890 device. DIMENSIONS 77.4mm x 15.9mm (depth when mounted, excluding bolt) WEIGHT 0.15 kg

KEY FEATURES

• Cellular/Wi-Fi/Bluetooth Antenna
• Works across multiple frequencies
• IP67/IP69K/IK09 protection
• GPS Antenna

KEY BENEFITS

• Flexible installation options
• Avoids unwanted interference
• Can be installed in multiple application environments
• Additional flexibility

 

**Please Note: The DSE123-01 has been discontinued and is no longer available.  The recommended replacement DSEG123 will be shipped** The DSE123 is an intelligent device that allows DSE load share modules to communicate with non-DSE control modules that are communicating over universal analogue load share lines. This means that DSE load share controls can be added to non-DSE load share systems. This flexibility allows existing systems to be expanded when the original controllers are no longer available. OVERALL SIZE 161 mm x 78 mm x 76 mm (6.3” x 3.1” x 3.0”) WEIGHT 0.3kg PRODUCT VARIANTS 0123-01 – 123 Analogue Loadshare Lines Interface

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 150 mA at 12 V, 80 mA at 24 V MAXIMUM STANDBY CURRENT 150 mA at 12 V, 80 mA at 24 V  

The DSE123 is an intelligent device that allows DSE load share modules to communicate with non-DSE control modules that are communicating over universal analogue load share lines. This means that DSE load share controls can be added to non-DSE load share systems. This flexibility allows existing systems to be expanded when the original controllers are no longer available. OVERALL SIZE 161 mm x 78 mm x 76 mm (6.3” x 3.1” x 3.0”) WEIGHT 0.3kg PRODUCT VARIANTS 0123-01 – 123 Analogue Loadshare Lines Interface

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 150 mA at 12 V, 80 mA at 24 V MAXIMUM STANDBY CURRENT 150 mA at 12 V, 80 mA at 24 V  

**Please Note: The DSE124 (0124-02 (No Fibre Optic) has been discontinued. The substitute will be DSE124 (0124-01 Fibre Obtic) for the replacement. The DSE124 CANbus extender has been designed to extend a multi-set comms load share link or engine CANbus. OVERALL SIZE 134 mm x 77 mm x 49 mm (5.3” x 3.0” x 1.9”) WEIGHT 0.2kg PRODUCT VARIANTS 0124-01 – 124 Canbus Extender (Fibre Optic) 0124-02 – 124 Canbus Extender (No Fibre Optic)

DC SUPPLY 

MINIMUM SUPPLY VOLTAGE 8 V continuous CRANKING DROPOUTS Able to survive 0V for 50mS providing the supply was at least 10V before the dropout and recovers to 5 volts afterwards. MAX OPERATING SUPPLY VOLTAGE 35V continuous. MAX OPERATING SUPPLY CURRENT 191mA at 12V, 99mA at 24V. Digital input grounded, passing MSC protocol at 75% bus capacity, Fibre port fitted. MAXIMUM STANDBY CURRENT

The DSE124 CANbus extender has been designed to extend a multi-set comms load share link or engine CANbus. OVERALL SIZE 134 mm x 77 mm x 49 mm (5.3” x 3.0” x 1.9”) WEIGHT 0.2kg PRODUCT VARIANTS 0124-01 – 124 Canbus Extender (Fibre Optic) 0124-02 – 124 Canbus Extender (No Fibre Optic)

DC SUPPLY 

MINIMUM SUPPLY VOLTAGE 8 V continuous CRANKING DROPOUTS Able to survive 0V for 50mS providing the supply was at least 10V before the dropout and recovers to 5 volts afterwards. MAX OPERATING SUPPLY VOLTAGE 35V continuous. MAX OPERATING SUPPLY CURRENT 191mA at 12V, 99mA at 24V. Digital input grounded, passing MSC protocol at 75% bus capacity, Fibre port fitted. MAXIMUM STANDBY CURRENT

The DSE125 MSC Converter has been developed to enable DSE55xx and DSE75xx MSC links to interface with MSC links containing DSE8xxx control modules. The DSE125 achieves this by having MSC link connections for all three-module types. When connected the system functionality mirrors the DSE55xx and DSE75xx control modules. OVERALL SIZE 134 mm x 77 mm x 49 mm (5.3” x 3.0” x 1.9”) WEIGHT 0.18kg PRODUCT VARIANTS 0125-01 – 125 MSC Converter

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS providing the supply was at least 10 V before the dropout and recovers to 5 V afterwards. MAXIMUM OPERATING CURRENT 130 mA at 12 V, 70 mA at 24 V MAXIMUM STANDBY CURRENT 65 mA at 12 V, 35 mA at 24 V  

The DSE160 Self-Seeking Power Supply has been designed for use with DSE3xx control modules. The DSE160 can be supplied from a mains (utility), generator or battery and provides a power supply output that gives DC power to the ATS controller. When the mains (utility) supply fails the DSE160 automatically switches to providing generator or battery power. Three red LEDs on the front of the unit show the operating status at all times. The DSE160 is available in 12 and 24 volt versions and provides comprehensive short circuit protection. OVERALL 136 mm x 140 mm x 63 mm (5.4” x 5.5” x 2.5”) WEIGHT 0.4kg PRODUCT VARIANTS 0160-00 – 12 Volt Self Seeking Power Supply (110v-277v 50.60Hz) 0160-01 – 24 Volt Self Seeking Power Supply (110v-277v 50/60Hz)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT

OUTPUT 1 A DC at 12 V DC 1 A DC at 24 V DC

The DSE160 Self-Seeking Power Supply has been designed for use with DSE3xx control modules. The DSE160 can be supplied from a mains (utility), generator or battery and provides a power supply output that gives DC power to the ATS controller. When the mains (utility) supply fails the DSE160 automatically switches to providing generator or battery power. Three red LEDs on the front of the unit show the operating status at all times. The DSE160 is available in 12 and 24 volt versions and provides comprehensive short circuit protection. OVERALL 136 mm x 140 mm x 63 mm (5.4” x 5.5” x 2.5”) WEIGHT 0.4kg PRODUCT VARIANTS 0160-00 – 12 Volt Self Seeking Power Supply (110v-277v 50.60Hz) 0160-01 – 24 Volt Self Seeking Power Supply (110v-277v 50/60Hz)

AC SUPPLY

VOLTAGE RANGE 90 V to 305 V (L-N) FREQUENCY RANGE 48 Hz to 64 Hz (L-N)

DC OUTPUT

OUTPUT 1 A DC at 12 V DC 1 A DC at 24 V DC

The DSE2130 is an input expansion module providing 8 additional inputs to the control module.  Four of these can be configured for use as analogue inputs.  Up to 4 x DSE2130 modules can be linked together to provide up to 32 additional inputs. Designed to give greater flexibility for meeting complex industry generator control specifications. All configurations are controlled within the host control module. OVERALL SIZE 134 mm x 76 mm x 49 mm (5.3” x 3.0” x 1.9”) WEIGHT 0.18kg PRODUCT VARIANTS 2130-00 – 2130 Input Expansion Module

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking.

The DSE2131 is a ratiometric input expansion module providing 10 additional inputs to the control module.  Up to 4 x DSE2131 modules can be linked together to provide up to 40 additional inputs. Designed to give greater input flexibility for meeting complex industry generator control specifications. Inputs can be configured to connect to resistive sensors, 0-10 V DC signals or 4-20mA signals, analogue inputs. All configurations are controlled from within the host control module. OVERALL SIZE 165 mm x 76 mm x 49 mm (6.5” x 3.0” x 1.9”) WEIGHT 0.22kg PRODUCT VARIANTS 2131-01 – 2131 Ratiometric Input Expansion Module

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8V to 35V continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs will not be maintained during cranking. MAXIMUM OPERATING CURRENT 292 mA at 12 V, 167 mA at 24 V MAXIMUM STANDBY CURRENT 101 mA at 12 V, 66 mA at 24 V INPUTS 10 inputs configurable for digital/resistive (3k ohms) 4-20 mA and 0-10 V DC  

The DSE2133 is an RTD/thermocouple input expansion module providing 8 additional inputs to the control module.  Up to 4 DSE2133 modules can be linked together to provide up to 32 additional inputs. Designed to give greater input flexibility for meeting complex industry generator control specifications. Inputs can be configured as RTD or thermocouple and are controlled from within the host control module. OVERALL SIZE 165 mm x 76 mm x 49 mm (6.5” x 3.0” x 1.9”) WEIGHT 0.22kg PRODUCT VARIANTS 2133-01 – 2133 RTD/Thermocouple Input Expansion Module

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8V to 35V continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs will not be maintained during cranking. MAXIMUM OPERATING CURRENT 292 mA at 12 V, 167 mA at 24 V MAXIMUM STANDBY CURRENT 101 mA at 12 V, 66 mA at 24 V

INPUT

8 inputs configurable as RTD/Thermocouple  

The DSE2152 is an analogue output expansion module providing 6 additional configurable outputs to the control system.  Up to 4 x DSE2152 modules can be linked together to provide up to 24 additional output options. Designed to give  greater output flexibility for meeting complex industry generator control specifications. The 6 outputs can be configured as 0-10 V or 4-20mA.  All configurations are controlled within the host control module. OVERALL SIZE 165 mm x 76 mm x 49 mm (6.5” x 3.0” x 1.9”) WEIGHT 0.24kg PRODUCT VARIANTS 2152-01 – 2152 Analogue Output Expansion Module

DC SUPPLY

8V to 35V continuous

CRANKING DROPOUTS

Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs will not be maintained during cranking.

MAXIMUM OPERATING CURRENT

56 mA at 12 V, 20 mA at 24 V

OUTPUT

OUTPUT A, B, C & D Non-Isolated Configurable As: 4 – 20 mA DC or 0 V to 10 V DC OUTPUT E & F Optional Isolation Configurable As: 4 – 20 mA DC or 0 V to 10 V DC  

The DSE2157 is an output relay expansion module providing 8 additional outputs to the control system. Up to 10 x DSE2157 modules can be linked to together to provide increased output options. Designed to give greater output flexibility for meeting complex industry generator control specifications.  The module includes eight configurable relay contacts with LED indicators. These can be configured as 4 normally open and 4 normally closed. All configurations are controlled within the host control module. OVERALL SIZE 165 mm x 76 mm x 49 mm (6.5” x 3.0” x 1.9”) WEIGHT 0.28kg PRODUCT VARIANTS 2157-01 – 2157 Output Expansion Module

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking.

The DSE2541 Remote Battery Charger Display Module has been designed to work with all intelligent and enclosed battery chargers. The module displays information to the operator on charge output, charge cycle, mains (utility) supply status and indicates when fault conditions are present. The DSE2541 enables the user to control a battery charger remotely via the front panel buttons. The DSE2541 and its connected charger can be configured using the front panel buttons. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.7”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6” x 3.6”) MAXIMUM PANEL THICKNESS 8.0mm (0.3”) WEIGHT 0.24kg PRODUCT VARIANTS 2541-02 - 2541 Remote Battery Charger Display Module

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 80 mA at 12 V, 75 mA at 24 V MAXIMUM STANDBY CURRENT 65 mA at 12 V, 60 mA at 24 V

FAULT OUTPUT

3 A at 30 V DC volt-free relay  

The DSE2548 is an output expansion module that can display a maximum of eight individual LED indications. Each indication is user configurable via the host module. Up to 10 DSE2548 modules can be linked together to provide up to 80 additional LED outputs. The DSE2548 can be located up to a maximum of 1 km (0.6 mile) away from the host control module. OVERALL SIZE 180 mm x 116 mm x 43 mm (7.1” x 4.6” x 1.7”) PANEL CUTOUT SIZE 154 mm x 98 mm (6.0” x 3.9”) MAXIMUM PANEL THICKNESS 8.0mm (0.3”) WEIGHT 0.36kg PRODUCT VARIANTS 2548-01 – 2548 Output Expansion Module

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 112 mA at 12 V, 53 mA at 24 V MAXIMUM STANDBY CURRENT 74 mA at 12 V, 35 mA at 24 V  

**Please Note: The DSE3110-02 (CAN) version has been discontinued and is no longer available.  If ordered, the recommended replacement DSE4520-35 will be shipped. The DSE3110 is an outstanding compact control module that provides a comprehensive range of features for single-set applications. The controller can be used in manual or auto start mode. OVERALL SIZE 98 mm x 79 mm x 40 mm (3.9” x 3.1” x 1.6”) PANEL CUTOUT SIZE 80 mm x 68 mm (3.1 ” x 2.7″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”)   WEIGHT  0.16kg PRODUCT VARIANTS 3110-02 – Manual & Auto Start Control Module (Can) 3110-01 – Manual & Auto Start Control Module (Mpu)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous

CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries

CHARGE FAIL/ EXCITATION 8 V to 35 V fixed power source 2.5 W

NOMINAL STANDBY CURRENT 23 mA at 12 V, 18 mA at 24 V

MAXIMUM OPERATING CURRENT 35 mA at 12 V, 30 mA at 24 V

OUTPUTS OUTPUT A (FUEL) 2 A DC at supply voltage OUTPUT B (START) 2 A DC at supply voltage AUXILIARY OUTPUTS C & D 2 A DC at supply voltage

GENERATOR 

VOLTAGE RANGE 15 V – 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz

MAGNETIC PICK-UP 

VOLTAGE RANGE +/- 0.5 V to 70 V FREQUENCY RANGE 10,000 Hz (max)  

The DSE3110 is an outstanding compact control module that provides a comprehensive range of features for single-set applications. The controller can be used in manual or auto start mode. OVERALL SIZE 98 mm x 79 mm x 40 mm (3.9” x 3.1” x 1.6”) PANEL CUTOUT SIZE 80 mm x 68 mm (3.1 ” x 2.7″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”)   WEIGHT  0.16kg PRODUCT VARIANTS 3110-02 – Manual & Auto Start Control Module (Can) 3110-01 – Manual & Auto Start Control Module (Mpu)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous

CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries

CHARGE FAIL/ EXCITATION 8 V to 35 V fixed power source 2.5 W

NOMINAL STANDBY CURRENT 23 mA at 12 V, 18 mA at 24 V

MAXIMUM OPERATING CURRENT 35 mA at 12 V, 30 mA at 24 V

OUTPUTS OUTPUT A (FUEL) 2 A DC at supply voltage OUTPUT B (START) 2 A DC at supply voltage AUXILIARY OUTPUTS C & D 2 A DC at supply voltage

GENERATOR 

VOLTAGE RANGE 15 V – 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz

MAGNETIC PICK-UP 

VOLTAGE RANGE +/- 0.5 V to 70 V FREQUENCY RANGE 10,000 Hz (max)  

The DSE3110 is an outstanding compact control module that provides a comprehensive range of features for single-set applications. The controller can be used in manual or auto start mode. OVERALL SIZE 98 mm x 79 mm x 40 mm (3.9” x 3.1” x 1.6”) PANEL CUTOUT SIZE 80 mm x 68 mm (3.1 ” x 2.7″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”)   WEIGHT  0.16kg PRODUCT VARIANTS 3110-02 – Manual & Auto Start Control Module (Can) 3110-01 – Manual & Auto Start Control Module (Mpu)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous

CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries

CHARGE FAIL/ EXCITATION 8 V to 35 V fixed power source 2.5 W

NOMINAL STANDBY CURRENT 23 mA at 12 V, 18 mA at 24 V

MAXIMUM OPERATING CURRENT 35 mA at 12 V, 30 mA at 24 V

OUTPUTS OUTPUT A (FUEL) 2 A DC at supply voltage OUTPUT B (START) 2 A DC at supply voltage AUXILIARY OUTPUTS C & D 2 A DC at supply voltage

GENERATOR 

VOLTAGE RANGE 15 V – 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz

MAGNETIC PICK-UP 

VOLTAGE RANGE +/- 0.5 V to 70 V FREQUENCY RANGE 10,000 Hz (max)  

**Please Note: The DSE3210 has been listed as discontinued, we may carry inventory until stock is depleted. The recommended replacement DSE3110 (provides same functionality but does not offer a key switch variant). The DSE3210 is an outstanding compact control module that provides a comprehensive range of features for single-set applications. The controller can be used in manual or auto start mode. OVERALL SIZE 98 mm x 79 mm x 40 mm (3.9” x 3.1” x 1.6”) PANEL CUTOUT SIZE 80 mm x 68 mm (3.1 ” x 2.7″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.18kg PRODUCT VARIANTS 3210-01 – 3210 Manual & Auto Start Control Module (Mpu)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries CHARGE FAIL/ EXCITATION 8 V to 35 V fixed power source 2.5 W NOMINAL STANDBY CURRENT 35 mA at 12 V, 30 mA at 24 V MAXIMUM OPERATING CURRENT 55 mA at 12 V, 60 mA at 24 V

OUTPUTS

OUTPUT A (FUEL) 2 A DC at supply voltage OUTPUT B (START) 2 A DC at supply voltage AUXILIARY OUTPUTS C,D 2 A DC at supply voltage

GENERATOR

VOLTAGE RANGE 15 V – 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz

MAGNETIC PICK UP

VOLTAGE RANGE +/- 0.5 V to 70 V FREQUENCY RANGE 10,000 Hz (max)  

The DSE327 is an Automatic Transfer Switch Control Module designed to monitor the voltage of an incoming AC supply from two different sources. This could be from both generator or mains (utility), or a combination of both. The module monitors S1 (Source 1) and in the event of a failure issues a start command to S2 (Source 2). The DSE327 can be ordered in 110 V and 230 V variants. Once S2 is available and producing an output within limits, the module controls the transfer device and switches the load from S1 to S2. Once the S1 supply returns to within limits, the module commands a load return to S1 and shuts down S2. Various timing sequences are available to prevent nuisance starting on minor supply breaks. OVERALL SIZE 72 mm x 90.5 mm x 65 mm (2.8” x 3.6” x 2.6”) WEIGHT 0.3 kg PRODUCT VARIANTS 0327-01 - 327 Auto Transfer Switch Control Module (230 Volt) 0327-02 - 327 Auto Transfer Switch Control Module (110 Volt) 0327-03 - 327 Auto Transfer Switch Control Module (230 Volt - 10 Second Delay)

MAXIMUM OPERATING/STANDBY CURRENT

VOLT FREE OUTPUTS

The DSE327 is an Automatic Transfer Switch Control Module designed to monitor the voltage of an incoming AC supply from two different sources. This could be from both generator or mains (utility), or a combination of both. The module monitors S1 (Source 1) and in the event of a failure issues a start command to S2 (Source 2). The DSE327 can be ordered in 110 V and 230 V variants. Once S2 is available and producing an output within limits, the module controls the transfer device and switches the load from S1 to S2. Once the S1 supply returns to within limits, the module commands a load return to S1 and shuts down S2. Various timing sequences are available to prevent nuisance starting on minor supply breaks. OVERALL SIZE 72 mm x 90.5 mm x 65 mm (2.8” x 3.6” x 2.6”) WEIGHT 0.3 kg PRODUCT VARIANTS 0327-01 - 327 Auto Transfer Switch Control Module (230 Volt) 0327-02 - 327 Auto Transfer Switch Control Module (110 Volt) 0327-03 - 327 Auto Transfer Switch Control Module (230 Volt - 10 Second Delay)

MAXIMUM OPERATING/STANDBY CURRENT

VOLT FREE OUTPUTS

The DSE331 Automatic Transfer Switch Control Module monitors the voltage and frequency of an incoming AC supply from two different sources. These sources can be generator or mains (utility), or a combination of both. The control module monitors Source 1 (S1) and Source 2(S2). When a failure occurs a start command is issued to the inactive source to take over the load. The module will return the load to the mains (utility) as soon as this becomes available. OVERALL SIZE 180 mm x 116 mm x 42 mm (7.1” x 4.6” x 1.7”) PANEL CUTOUT SIZE 154 mm x 98 mm (6.0” x 3.9”) MAXIMUM PANEL THICKNESS 8.0mm (0.3”) WEIGHT 0.36kg PRODUCT VARIANTS 0331-01 - 331 Auto Transfer Switch Control Module - 12/24 Volt DC Supply

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries.  LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 168 mA at 12 V, 80 mA at 24 V MAXIMUM STANDBY CURRENT 39 mA at 12 V, 20 mA at 24 V

OUTPUTS

OUTPUT A & B Normally open volt-free output 8 A DC at 35 V DC OUTPUT C & D Changeover volt-free output 8 A DC at 35 V DC AUXILLARY OUTPUT E, F, G & H 2 A DC at supply voltage S1 & S2 VOLTAGE RANGE 15 V to 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz  

The DSE334 Automatic Transfer Switch Control Module monitors the voltage and frequency of an incoming AC supply from two different sources. These sources can be generator or mains (utility), or a combination of both. The control module monitors Source 1 (S1) and Source 2(S2). When a failure occurs a start command is issued to the inactive source to take over the load. The module will return the load to the mains (utility) as soon as this becomes available. OVERALL SIZE 215 mm x 158 mm x 42 mm (8.5” x 6.2” x 1.6”) PANEL CUTOUT SIZE 182 mm x 137 mm (7.2” x 5.4”) MAXIMUM PANEL THICKNESS 8.0mm (0.3”) WEIGHT 0.52kg PRODUCT VARIANTS 0334-01 - 334 Auto Transfer Switch Control Module - 12/24 Volt DC Supply

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 292 mA at 12 V, 167 mA at 24 V MAXIMUM STANDBY CURRENT 101 mA at 12 V, 66 mA at 24 V MAINS (UTILITY) VOLTAGE RANGE 15 V to 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz

OUTPUTS

OUTPUT A (MAINS/UTILITY/S1) Normally closed volt-free output 8 A AC at 250 V AC OUTPUT B (GENERATOR/S2) Normally open volt-free output 8 A AC at 250 V AC OUTPUT C (START AND RUN) Normally closed volt-free output 8 A DC at 35 V DC (UL Rating 30 V) OUTPUT D Changeover volt-free output 8 A AC at 250 V AC OUTPUT E Normally open volt-free output 8 A AC at 250 V AC

GENERATOR

VOLTAGE RANGE 15 V to 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz  

**Please Note: The DSE335-01 has been discontinued and is no longer available. If ordered, the recommended replacement DSE335-11 will be shipped. Important Information: The module wiring and cut-out for the 0335-11 is the same as the module wiring and cut-out for the 0335-01. 0335-11 differences to 0335-01:

• No RS232 or Modem support (Functionality removed).
• Configurable close transition menu enhanced down to <100 ms.
• Switching schemes combined into a single scheme, reduced from 3.
• S1 and S2 sensing increased to 415 V AC, ensuring module fully supports 600 V 3-phase systems.
• Configurable LEDs are bi-colour for improved status indication.
• Single label front.

The DSE335 Automatic Transfer Switch Control Module has been expertly developed to monitor the voltage and frequency of an incoming AC supply from two different sources. These sources can be generator or mains (utility), or a combination of both. The control module monitors Source 1 (S1) and Source 2(S2). When a failure occurs a start command is issued to the inactive source to take over the load. The module will return the load to the mains (utility) as soon as this becomes available. OVERALL SIZE 240 mm x 181 mm x 42 mm (9.4” x 7.1” x 1.6”) PANEL CUTOUT SIZE 220 mm x 160 mm (8.7” x 6.3”) MAXIMUM PANEL THICKNESS 8.0mm (0.3”) WEIGHT 0.9kg PRODUCT VARIANTS 0335-01 - 335 Auto Transfer Switch Control Module - 12/24 Volt DC Supply

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 480 mA at 12 V, 360 mA at 24 V MAXIMUM STANDBY CURRENT 126 mA at 12 V, 96 mA at 24 VS1

S1

VOLTAGE RANGE 15 V to 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz

OUTPUTS

OUTPUTS A & E Normally closed volt-free output 8 A AC at 250 V AC OUTPUTS B & F Normally open volt-free output 8 A AC at 250 V AC OUTPUT C & D Changeover volt-free output 8 A AC at 250 V AC AUXILIARY OUTPUTS G,H,I,J,K & L 2 A DC at supply voltage

S2

VOLTAGE RANGE 15 V to 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz  

DSE335-11 - Automatic Transfer Switch Controller (Replacement for DSE335-01) Important Information: The module wiring and cut-out for the 0335-11 is the same as the module wiring and cut-out for the 0335-01. 0335-11 differences to 0335-01:

• No RS232 or Modem support (Functionality removed).
• Configurable close transition menu enhanced down to <100 ms.
• Switching schemes combined into a single scheme, reduced from 3.
• S1 and S2 sensing increased to 415 V AC, ensuring module fully supports 600 V 3-phase systems.
• Configurable LEDs are bi-colour for improved status indication.
• Single label front.

The DSE335 Automatic Transfer Switch Control Module has been expertly developed to monitor the voltage and frequency of an incoming AC supply from two different sources. These sources can be generator or mains (utility), or a combination of both. The control module monitors Source 1 (S1) and Source 2(S2). When a failure occurs a start command is issued to the inactive source to take over the load. The module will return the load to the mains (utility) as soon as this becomes available. OVERALL SIZE 240 mm x 181 mm x 42 mm (9.4” x 7.1” x 1.6”) PANEL CUTOUT SIZE 220 mm x 160 mm (8.7” x 6.3”) MAXIMUM PANEL THICKNESS 8.0mm (0.3”) WEIGHT 0.9kg PRODUCT VARIANTS 0335-01 - 335 Auto Transfer Switch Control Module - 12/24 Volt DC Supply

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 480 mA at 12 V, 360 mA at 24 V MAXIMUM STANDBY CURRENT 126 mA at 12 V, 96 mA at 24 VS1

S1

VOLTAGE RANGE 15 V to 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz

OUTPUTS

OUTPUTS A & E Normally closed volt-free output 8 A AC at 250 V AC OUTPUTS B & F Normally open volt-free output 8 A AC at 250 V AC OUTPUT C & D Changeover volt-free output 8 A AC at 250 V AC AUXILIARY OUTPUTS G,H,I,J,K & L 2 A DC at supply voltage

S2

VOLTAGE RANGE 15 V to 333 V AC (L-N) FREQUENCY RANGE 3.5 Hz to 75 Hz  

**Please Note: The DSE402 (0402-04 (HZ) has been discontinued. The replacement will be the DSE402 (0402-03 (MPU). The DSE402 MKII is a waterproof Auto/Manual Start Control Module designed for generator and engine only applications. The intelligent design combines smart features with a waterproof key switch and enclosure to provide an excellent control option for wet/humid environments. OVERALL SIZE 157 mm x 111 mm x 60 mm (6.2” x 4.4” x 2.4”) Excludes Key Switch PANEL CUTOUT SIZE 132 mm x 84 mm (5.2 ” x 3.4″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.45kg PRODUCT VARIANTS 0402-03 – 402 MKII Waterproof Engine Control Module (Mpu) 0402-04 – 402 MKII Waterproof Engine Control Module (Hz) 0402-05 – 402 MKII Waterproof Engine Control Module with ETS (Mpu) 0402-06 – 402 MKII Waterproof Engine Control Module with ETS (Hz)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. MAXIMUM OPERATING CURRENT 120 mA at 12 V, 170 mA at 24 V TYPICAL OPERATING CURRENT 60 mA at 12 V, 75 mA at 24 V In stop position consumption is zero. CHARGE/FAIL EXCITATION RANGE 0 V to 35 V

OUTPUTS

FUEL 15 A DC at supply voltage START 15 A DC at supply voltage PRE-HEAT 2 A DC at supply voltage  

**Please Note: The DSE402-03 has been discontinued and is no longer available. If ordered, the recommended replacement DSE402-04 will be shipped. The DSE402 MKII is a waterproof Auto/Manual Start Control Module designed for generator and engine only applications. The intelligent design combines smart features with a waterproof key switch and enclosure to provide an excellent control option for wet/humid environments. OVERALL SIZE 157 mm x 111 mm x 60 mm (6.2” x 4.4” x 2.4”) Excludes Key Switch PANEL CUTOUT SIZE 132 mm x 84 mm (5.2 ” x 3.4″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.45kg PRODUCT VARIANTS 0402-03 – 402 MKII Waterproof Engine Control Module (Mpu) 0402-04 – 402 MKII Waterproof Engine Control Module (Hz) 0402-05 – 402 MKII Waterproof Engine Control Module with ETS (Mpu) 0402-06 – 402 MKII Waterproof Engine Control Module with ETS (Hz)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. MAXIMUM OPERATING CURRENT 120 mA at 12 V, 170 mA at 24 V TYPICAL OPERATING CURRENT 60 mA at 12 V, 75 mA at 24 V In stop position consumption is zero. CHARGE/FAIL EXCITATION RANGE 0 V to 35 V

OUTPUTS

FUEL 15 A DC at supply voltage START 15 A DC at supply voltage PRE-HEAT 2 A DC at supply voltage  

**Please Note: The DSE4510-35 has been discontinued and is no longer available. If ordered, the recommended replacement DSE4520-35 will be shipped. The DSE4510 MKII is a compact Auto Start Control Module that has been developed to provide an outstanding range of features within a compact enclosure. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.5”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6″ x 3.6″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.26kg PRODUCT VARIANTS 4510-05 – 4510 Auto Start Control Module (Ct, Rtc) 4510-06 – 4510 Auto Start Control Module (Ct, Rtc, Htr)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 85 mA at 12 V, 96 mA at 24 V MAXIMUM STANDBY CURRENT 51 mA at 12 V, 47 mA at 24 V MAXIMUM SLEEP CURRENT 35 mA at 12 V, 32 mA at 24 V MAXIMUM DEEP SLEEP CURRENT <10 uA at 12 V, <10 uA at 24 V

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTs C & D 2 A DC at supply voltage

GENERATOR

VOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz  

**Please Note: The DSE4510-06 has been discontinued and is no longer available. If ordered, the recommended replacement DSE4520-35 will be shipped. The DSE4510 MKII is a compact Auto Start Control Module that has been developed to provide an outstanding range of features within a compact enclosure. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.5”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6″ x 3.6″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.26kg PRODUCT VARIANTS 4510-05 – 4510 Auto Start Control Module (Ct, Rtc) 4510-06 – 4510 Auto Start Control Module (Ct, Rtc, Htr)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 85 mA at 12 V, 96 mA at 24 V MAXIMUM STANDBY CURRENT 51 mA at 12 V, 47 mA at 24 V MAXIMUM SLEEP CURRENT 35 mA at 12 V, 32 mA at 24 V MAXIMUM DEEP SLEEP CURRENT <10 uA at 12 V, <10 uA at 24 V

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTs C & D 2 A DC at supply voltage

GENERATOR

VOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz  

The DSE4520 MKII is a compact Auto Mains (Utility) Failure Control Module that has been developed to provide an outstanding range of features within a compact enclosure. THE MODULE CAN BE CONFIGURED FOR USE AS AN AUTO START CONTROL MODULE. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.5”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6" x 3.6") MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.26kg PRODUCT VARIANTS 4520-05 - 4520 Auto Mains (Utility) Failure Control Module (Ct, Rtc)  

SPECIFICATION

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 85 mA at 12 V, 96 mA at 24 V MAXIMUM STANDBY CURRENT 51 mA at 12 V, 47 mA at 24 V MAXIMUM SLEEP CURRENT 35 mA at 12 V, 32 mA at 24 V MAXIMUM DEEP SLEEP CURRENT <10 uA at 12 V, <10 uA at 24 V

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTs C & D 2 A DC at supply voltage ­­

GENERATOR

VOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz  

The DSE4520 MKII is a compact Auto Mains (Utility) Failure Control Module that has been developed to provide an outstanding range of features within a compact enclosure. THE MODULE CAN BE CONFIGURED FOR USE AS AN AUTO START CONTROL MODULE. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.5”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6" x 3.6") MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.26kg PRODUCT VARIANTS 4520-05 - 4520 Auto Mains (Utility) Failure Control Module (Ct, Rtc)  

SPECIFICATION

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 85 mA at 12 V, 96 mA at 24 V MAXIMUM STANDBY CURRENT 51 mA at 12 V, 47 mA at 24 V MAXIMUM SLEEP CURRENT 35 mA at 12 V, 32 mA at 24 V MAXIMUM DEEP SLEEP CURRENT <10 uA at 12 V, <10 uA at 24 V

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTs C & D 2 A DC at supply voltage ­­

GENERATOR

VOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz  

**Please Note: The DSE4520-36 has been discontinued and is no longer available. If ordered, the recommended replacement DSE4520-05 or DSE4520-35 will be shipped. The DSE4520 MKII is a compact Auto Mains (Utility) Failure Control Module that has been developed to provide an outstanding range of features within a compact enclosure. THE MODULE CAN BE CONFIGURED FOR USE AS AN AUTO START CONTROL MODULE. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.5”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6" x 3.6") MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.26kg PRODUCT VARIANTS 4520-05 - 4520 Auto Mains (Utility) Failure Control Module (Ct, Rtc)  

SPECIFICATION

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 85 mA at 12 V, 96 mA at 24 V MAXIMUM STANDBY CURRENT 51 mA at 12 V, 47 mA at 24 V MAXIMUM SLEEP CURRENT 35 mA at 12 V, 32 mA at 24 V MAXIMUM DEEP SLEEP CURRENT <10 uA at 12 V, <10 uA at 24 V

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTs C & D 2 A DC at supply voltage ­­

GENERATOR

VOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz  

The DSE4610 is a compact Auto Start Control Module that has been developed to provide an outstanding range of features within a compact enclosure. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.5”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6″ x 3.6″) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.28kg PRODUCT VARIANTS 4610-03 – 4610 Auto Start Control Module (Mpu,Ct,Rtc)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 85 mA at 12 V, 96 mA at 24 V MAXIMUM STANDBY CURRENT 51 mA at 12 V, 47 mA at 24 V MAXIMUM SLEEP CURRENT 35 mA at 12 V, 32 mA at 24 V MAXIMUM DEEP SLEEP CURRENT <10 uA at 12 V, <10 uA at 24 V

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTs C & D 2 A DC at supply voltage

GENERATOR

VOLTAGE RANGE 15 V to 415 V AC (Ph-N) 26  to 719 V AC (Ph – Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz

MAGNETIC PICK-UP

VOLTAGE RANGE +/- 0.5 V to 70 V FREQUENCY RANGE 10,000 Hz (max)  

The DSE4620 is a compact Auto Mains (Utility) Failure Control Module that has been developed to provide an outstanding range of features within a compact enclosure. OVERALL SIZE 140 mm x 113 mm x 43 mm (5.5” x 4.4” x 1.5”) PANEL CUTOUT SIZE 118 mm x 92 mm (4.6" x 3.6") MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.28kg PRODUCT VARIANTS 4620-03 - 4620 Auto Mains (Utility) Failure Control Module (Mpu,Ct,Rtc)

SPECIFICATION

The DSE 6020 MKII is an Auto Mains (Utility) Failure Control Module developed to provide a wide range of operating and monitoring features for single diesel and gas gen-sets. OVERALL SIZE 216 mm x 158 mm x 43 mm (8.5” x 6.2” x 1.5”) PANEL CUTOUT SIZE 184 mm x 137 mm (7.2" x 5.3") MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.48kg PRODUCT VARIANTS 6020-03 - MKII Auto Mains (Utility) Failure Control Module 6020-04 - MKII Auto Mains (Utility) Failure Control Module (Htr)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 100 mA at 12 V, 105 mA at 24 V MAXIMUM STANDBY CURRENT 60 mA at 12 V, 55 mA at 24 V MAXIMUM SLEEP CURRENT 40 mA at 12 V, 35 mA at 24 V

GENERATOR & MAINS (UTILITY)

VOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz

INPUTS

DIGITAL INPUTS A to F Negative switching ANALOGUE INPUTS A to C Configurable as: Negative switching digital input 0 Ω to 480 Ω ANALOGUE INPUT D Configurable as: Negative switching digital input 0 V to 10 V 4 mA to 20 mA 0 Ω to 480 Ω

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTS C, D, E & F 2 A DC at supply voltage ­

**Please Note: The DSE6020-04 has been discontinued and is no longer available. If ordered, the recommended replacement DSE6020-03 will be shipped. The DSE 6020 MKII is an Auto Mains (Utility) Failure Control Module developed to provide a wide range of operating and monitoring features for single diesel and gas gen-sets. OVERALL SIZE 216 mm x 158 mm x 43 mm (8.5” x 6.2” x 1.5”) PANEL CUTOUT SIZE 184 mm x 137 mm (7.2" x 5.3") MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.48kg PRODUCT VARIANTS 6020-03 - MKII Auto Mains (Utility) Failure Control Module 6020-04 - MKII Auto Mains (Utility) Failure Control Module (Htr)

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous CRANKING DROPOUTS Able to survive 0 V for 50 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 100 mA at 12 V, 105 mA at 24 V MAXIMUM STANDBY CURRENT 60 mA at 12 V, 55 mA at 24 V MAXIMUM SLEEP CURRENT 40 mA at 12 V, 35 mA at 24 V

GENERATOR & MAINS (UTILITY)

VOLTAGE RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz

INPUTS

DIGITAL INPUTS A to F Negative switching ANALOGUE INPUTS A to C Configurable as: Negative switching digital input 0 Ω to 480 Ω ANALOGUE INPUT D Configurable as: Negative switching digital input 0 V to 10 V 4 mA to 20 mA 0 Ω to 480 Ω

OUTPUTS

OUTPUT A (FUEL) 10 A short term, 5 A continuous, at supply voltage OUTPUT B (START) 10 A short term, 5 A continuous, at supply voltage AUXILIARY OUTPUTS C, D, E & F 2 A DC at supply voltage ­

The DSE6110 MKIII is an Auto Start Control Module suitable for a wide variety of single, diesel or gas, genset applications. Monitoring an extensive number of engine parameters, the module will display warnings, shutdown and engine status information on the back-lit LCD screen, illuminated LEDs and remote PC. The module includes USB connection and dedicated DSENet® terminals for system expansion. The module is compatible with electronic (CAN) and non-electronic (magnetic pick-up/alternator sensing) engines and offers an extensive number of flexible inputs, outputs and extensive engine protections so the system can be easily adapted to meet the most demanding industry requirements. The extensive list of features includes enhanced event and performance monitoring, remote communications & PLC ? functionality. The modules can be easily configured using the DSE Configuration Suite PC software. Selected front panel editing is also available. OVERALL SIZE 216 mm x 158 mm x 43 mm (8.5” x 6.2” x 1.5”) PANEL CUTOUT SIZE 184 mm x 137 mm (7.2” x 5.3”) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.5kg PRODUCT VARIANTS 6110-05 – 6110 MKIII Auto Start Control Module

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous 5 V for up to 1 minute CRANKING DROPOUTS Able to survive 0 V for 100 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 260 mA at 12 V, 150 mA at 24 V MAXIMUM STANDBY CURRENT 145 mA at 12 V, 85 mA at 24 V CHARGE FAIL/EXCITATION RANGE 0 V to 35 V

GENERATOR & MAINS (UTILITY)

VOLTAGE  RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz

MAGNETIC PICKUP

VOLTAGE  RANGE +/- 0.5 V to 70 V FREQUENCY RANGE 10,000 Hz (max)

INPUTS

DIGITAL INPUTS A to H Negative switching ANALOGUE INPUTS A & D Configurable as: Negative switching digital input 0 V to 10 V sensor 4 mA to 20 mA sensor Resistive sensor ANALOGUE INPUTS B & C Configurable as: Negative switching digital input Resistive sensor

OUTPUTS

OUTPUT A & B (FUEL & START) 10 A DC at supply voltage AUXILIARY OUTPUTS C, D, E, F, G & H 2 A DC at supply voltage  

**Please Note: The DSE6110-35 has been discontinued and is no longer available. If ordered, the recommended replacement DSE6110-05 will be shipped. The DSE6110 MKIII is an Auto Start Control Module suitable for a wide variety of single, diesel or gas, genset applications. Monitoring an extensive number of engine parameters, the module will display warnings, shutdown and engine status information on the back-lit LCD screen, illuminated LEDs and remote PC. The module includes USB connection and dedicated DSENet® terminals for system expansion. The module is compatible with electronic (CAN) and non-electronic (magnetic pick-up/alternator sensing) engines and offers an extensive number of flexible inputs, outputs and extensive engine protections so the system can be easily adapted to meet the most demanding industry requirements. The extensive list of features includes enhanced event and performance monitoring, remote communications & PLC ?functionality. The modules can be easily configured using the DSE Configuration Suite PC software. Selected front panel editing is also available. OVERALL SIZE 216 mm x 158 mm x 43 mm (8.5” x 6.2” x 1.5”) PANEL CUTOUT SIZE 184 mm x 137 mm (7.2” x 5.3”) MAXIMUM PANEL THICKNESS 8.0 mm (0.3”) WEIGHT 0.5kg PRODUCT VARIANTS 6110-05 – 6110 MKIII Auto Start Control Module

DC SUPPLY

CONTINUOUS VOLTAGE RATING 8 V to 35 V Continuous 5 V for up to 1 minute CRANKING DROPOUTS Able to survive 0 V for 100 mS, providing supply was at least 10 V before dropout and supply recovers to 5 V. This is achieved without the need for internal batteries. LEDs and backlight will not be maintained during cranking. MAXIMUM OPERATING CURRENT 260 mA at 12 V, 150 mA at 24 V MAXIMUM STANDBY CURRENT 145 mA at 12 V, 85 mA at 24 V CHARGE FAIL/EXCITATION RANGE 0 V to 35 V

GENERATOR & MAINS (UTILITY)

VOLTAGE  RANGE 15 V to 415 V AC (Ph to N) 26 V to 719 V AC (Ph to Ph) FREQUENCY RANGE 3.5 Hz to 75 Hz

MAGNETIC PICKUP

VOLTAGE  RANGE +/- 0.5 V to 70 V FREQUENCY RANGE 10,000 Hz (max)

INPUTS

DIGITAL INPUTS A to H Negative switching ANALOGUE INPUTS A & D Configurable as: Negative switching digital input 0 V to 10 V sensor 4 mA to 20 mA sensor Resistive sensor ANALOGUE INPUTS B & C Configurable as: Negative switching digital input Resistive sensor

OUTPUTS

OUTPUT A & B (FUEL & START) 10 A DC at supply voltage AUXILIARY OUTPUTS C, D, E,  F, G & H 2 A DC at supply voltage